One end of the hollow aluminum shaft is fixed, and the other end is connected to a gear with an outside diameter of 40 cm as shown. The gear is subjected to a tangential gear force of 45 kN. The shear modulus of the aluminum is 2.8 × 1010 Pa. What are the maximum angle of twist and the shear stress in the shaft? 40 cm diameter- 120 cm D, - 7.5 cm - Do - 10 cm fixed F- 45000 N

One end of the hollow aluminum shaft is fixed, and the other end is connected to a gear with an outside diameter of 40 cm as shown. The gear is subjected to a tangential gear force of 45 kN. The shear modulus of the aluminum is 2.8 × 1010 Pa. What are the maximum angle of twist and the shear stress in the shaft? 40 cm diameter- 120 cm D, - 7.5 cm - Do - 10 cm fixed F- 45000 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid-circular shafts are connected by gears at B and C as shown below, and having the same diameter (D.). The shear modulus of the shafts is 75 GPa, All bearings allow free rotations of the shafts. Determine the rotation of free end A when a torque T is applied. L1 (mm) L2 (mm) Do (mm) T (N.m) 1105 480 44 58 L1 Fixed 60 m L2
The torques shown are applied to a 6 mm radius solid shaft with G = 70 GPa. Determine the maximum shear stress in the shaft and the rotation of end gear A with respect to fixed support E 40 Nm 280 Nm 05 m 150 N m 100 m 04 m (a)
A flange-and-bolt coupling between two shafts carries 12 bolts at a pitch diameter of 18 in. The shafts carry a torque of 50,000 ft-lb. Assuming that this torque is transmitted by shear across the 12 bolts and that these bolts are to be designed for a shear stress s3 = 3,000 lb/sq in., what is the bolt diameter?
TORSION An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa. DETERMINE: A. the relative angle of twist of gear D relative to gear A (in degrees) B. the direction of the rotation of A relative to D? PROVIDE FBD
A hallow steel shaft 2540 mm long must transmit torque of 34 KN-m. The total angle of twist must not exceed 3 degrees. The maximum shearing stress must not exceed 110 MPa. Find the inside diameter and the outside diameter of the shaft that meets these conditions. Use G = 83 GPa
A fixed-end shaft is subjected to torques T1 (Nm) and T2 (Nm) as shown in the figure. If the shear modulus of elasticity is Gahat= 20 GPa, and shaft diameters are D, (mm) and D2 (mm) determine the angle of twist at point C, ØCIA- D1=100mm D2=30mm T1=800NM T2=200NM D1=100mm T(Nm) B D2=30mm |T;(Nm) A L=300mm Section for point A =900mm Section for points B and C Results Table ОСА (rad.)-
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
Detailed solution would be appreciated thanks!!. The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress (in Pa) in the hollow shaft using the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70092104 Pa and angle of twist of 2.25ᴼ for the whole shaft. Use G = 83000000000 Pafor the shaft, x = 2.43 m, and y = 1.89 m. Round off the final answer to two decimal places.
A hollow steel shaft with an outside diameter of 41 mm and a wall thickness of 9 mm is subjected to a pure torque of T = 6300 N-m. The shear modulus of the steel is G = 87 GPa. Determine: (a) the maximum shear stress T in the shaft. (b) the magnitude of the angle of twist o in a 2.4-m length of shaft. Answers: (a) = i MPа. (b) p = i
The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G=11400 ksi] shafts with lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation of the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DA of gear D with respect to flange A. Answers: (a) T₁ = (b) P DIA Nc WWAMACOM Save for Later C 9.3808 = i 2.1378 e Textbook and Media NB L₁ B D TD ksi, 1₂: = i 14.5924 ksi. Attempts: 1 of 5 used Submit Answer
Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The shaft CFG is supported at two bearings, while shaft HJ is fixed at 'H' and supported by bearings at 'J. Determine the torques T 1 and T 2 if the twisting at gears C and G is required to be 0.05 rad. Take E=205GPA, G=70GPA 600 mm 75mm 600 mm 50mm 800mm G. T2