on a 10 mm thick plate 5.104 W/m³ heat generation takes place. Heat transfer coefficient of the plate50 W/m.°C One surface of the plate is insulated and the temperature of the other surface is T₂ plate 2 at the temperaturesurface at 20 C and heat convection coefficient of 20 W/m. It is in contact with the environment at C. One of the heat transfer Assuming that the temperature T2 temp distribution of the plate is continuous, temperature and maximum find the temperature Yalıtım. T2=? L=10 mm T-20 °C h=20 W/m°C

on a 10 mm thick plate 5.104 W/m³ heat generation takes place. Heat transfer coefficient of the plate50 W/m.°C One surface of the plate is insulated and the temperature of the other surface is T₂ plate 2 at the temperaturesurface at 20 C and heat convection coefficient of 20 W/m. It is in contact with the environment at C. One of the heat transfer Assuming that the temperature T2 temp distribution of the plate is continuous, temperature and maximum find the temperature Yalıtım. T2=? L=10 mm T-20 °C h=20 W/m°C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.16P: 3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer...

See similar textbooks

Similar questions

2.44 To determine the thermal conductivity of a long, solid 2.5-cm-diameter rod, one half of the rod was inserted into a furnace while the other half was projecting into air at . After steady state had been reached, the temperatures at two points 7.6 cm apart were measured and found to be and , respectively. The heat transfer coefficient over the surface of the rod exposed to the air was estimated to be 22.7 . What is thermal conductivity of the rod?
1.51 The inner wall of a rocket motor combustion chamber receives by radiation from a gas at . The convection heat transfer coefficient between the gas and the wall is . If the inner wall of the combustion chamber is at Problem 1.51 a temperature of , determine (a) the total thermal resistance of a unit area of the wall in and (b) the heat flux. Also draw the thermal circuit.
2.43 A turbine blade 6.3 cm long, with cross-sectional area and perimeter , is made of stainless steel . The temperature of the root, , is . The blade is exposed to a hot gas at , and the heat transfer coefficient is K. Determine the temperature of the blade tip and the rate of heat flow at the root of the blade. Assume that the tip is insulated.
The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.
An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
A thin-wall jacketed tank heated by condensing steam at one atmosphere contains 91 kg of agitated water. The heat transfer area of the jacket is 0.9m2 and the overall heat transfer coefficient U=227W/m2K based on that area. Determine the heating time required for an increase in temperature from 16C to 60C.
A steam pipe 200 mm in diameter passes through a large basement room. The temperature of the pipe wall is 500C, while that of the ambient air in the room is 20C. Determine the heat transfer rate by convection and radiation per unit length of steam pipe if the emissivity of the pipe surface is 0.8 and the natural convection heat transfer coefficient has been determined to be 10 W/m2K.
1.79 Consider the cooling of (a) a personal computer with a separate CPU and (b) a laptop computer. The reliable functioning of these machines depends on their effective cooling. Identify and briefly explain all modes of heat transfer involved in the cooling process.
1.49 A small oven with a surface area of is located in a room in which the walls and the air are at a temperature of . The exterior surface of the oven is at , and the next heat transfer by radiation between the oven’s surface and the surroundings is 586 W. If the average convection heat transfer coefficient between the oven and the surrounding air is 11 calculate (a) the net heat transfer between the oven and the surroundings in W, (b) the thermal resistance at the surface for radiation and convection, respectively, in K/W, and (c) the combined heat transfer coefficient in .
2.9 In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas-side and liquid-side convection heat transfer coefficients of 50 and , respectively. The wall that separates the gas and liquid streams is composed of a 2-cm thick oxide layer on the gas side and a 4-cm thick slab of stainless steel on the liquid side. There is a contact resistance between the oxide layer and the steel of . Determine the rate of heat loss from hot gases through the composite wall to the liquid.