oläi 8 The table below contains the information about Areas of cross-sections of road. Calculate the volumes of the earth work. Distance(m) Areas(m) 30 60 100 140 48 37.5 25.345 13.854 14.145 3497.863 m3 3498.386 m3 3489.863 m3 3498.863 m3

Q: Q1 The table below contains the cross - sections Areas of road Calculate the volumes of the earth…

A: Given; Distance (m) 0 30 60 100 140 Area (m2) 48 37.5 25.345 13.854 14.145

Q: Calculate straight line equation for following Transportation data Road Length, X (km) Number of…

A: Given table is about the road length in Km and number of vehicles on that span of road

Q: 1. Complete the differential level notes shown below, perform the customary arithmetic check,…

A: Leveling is the process in which we measure the levels of the various point of field in a linear or…

Q: 1. Complete the differential level notes shown below, perform the customary arithmetic check,…

A: Formulas Used: 1.Mean Rdg= (Upper + Middle + Lower ) Rdg/ 3  2.S = (Upper - Lower) Rdg  3. H.I =…

Q: If the collar at A is fixed to the member and can slide vertically along the vertical shaft which…

A: Hi there! you haven't mentioned your ID so, I have taken the values of A and Y from the given…

Q: From the given data, what is the volume with prismoidal correction? VE = 4096.25 m3; C1 = 5 m.; C2 =…

A:

Q: The table below contains the cross-sections Areas of road Calculate the volumes of the earth work…

A: h1=30m h2=60m

Q: This question may be completed using a Close program on a graphing calculator where necessary. Using…

A: Given that,the road secants C-F and B-G, road lengths G-F and G-H.

Q: Ordinates of a 3-h unit hydrograph are given below. Find the ordinates of 6 hr unit hydrograph using…

A:

Q: The diagram shows the cross-section of a creek, with the depths of the creek shown in meters, at…

A:

Q: Problem 1 Determine the vertical displacement at joint H of the truss below using the method of…

A: Given: Area of the member, A = 4.5 in2 Modulus of elasticity, E = 29000 ksi To find: Vertical…

Q: Q2/. The areas within the contour lines at the site as follows: Calculate the volume of water…

A: Given that: Counters (m) 90 88 86 84 82 80 78 Areas (m2) 4760 4310 3770 2960 2190 1640 8400

Q: The table below contains the cross-sections Areas of road Calculate the volumes of the earth work…

A: Consider the given data. The formula to calculate the volume is given by, V=A1+A22width

Q: Draw the following figure using AutoCAD commands R14 Ø86 R49 30 R18 R7 29 R14 Ø53 Ø38 96 192 192 96

A: Question being asked here is to draw the given figure using the AUTO CAD software. And the following…

Q: The following is a page of an old level field book, in which some of the missing entries are shown.…

A:

Q: Determine M, if f, = 420 MPa and f'c = 28 MPa. %3D 75 75 75 75 mm mm mm mm 150 mm 75 mm 75 mm 825 mm…

A:

Q: 200 mm 30 mm -25 mm V В 250 mm 30 mm 125 mm If calculating the shear stress at point B, what is the…

A: Step 1

Q: Do not include the unit in writing the answer. Express all values up to 3 decimal places. You can…

A: Complete the table above?

Q: Reference Line. A1 Neutral Axis (N.A) 250 mm A2 50 mm 40 mm 220 mm

A:

Q: 3. Complete the differential level notes shown below and perform the customary arithmetic check.…

A:

Q: Then calculate the cross-section for section E, the image below:

A: Answer  Since we are not given any specific method, we can determine the cross section at E by using…

Q: The table below contains the cross- sections Areas of road Calculate the volumes of the earth work…

A:

Q: Q1-) Fill the table according to given measurements. Present your answers in degree and minute form.

A: We need to find Bearing, Back Bearing, Azimuth and Back azimuths

Q: Determine the reaction at the roller sl 100 N 200 N 300 N 60 45 30 1 m 1 m

A:

Q: Q1/The table below contains the cross- sections Areas of road Calculate the volumes of the earth…

A: Given that: Distance (m) 0 30 60 120 180 Area (m2) 48.000 37.500 25.345 13.854 14.145

Q: The table below contains the information about Areas of cross-sections of road. .Calculate the…

A: Using Simpsons rule two times since there are different interval lengths. Then summing up the two…

Q: Calculate harmonic mean for velocity (kmph) data of vehicles moving on an expressway 2 86 04

A: Given: S. No. Velocity, x kmph 1 92 2 71 3 90 4 87 5 96 6 98 7 94 8 60 9 80…

Q: Q4) The areas within the underwater contour lines of a reservoir are as follows: Contour (m) 184…

A: The methods used for calculating the volume of reservoir with contours and area measurements are 1.…

Q: 26 38 48 55 22 29 45 55 24 35 46 54 35 41 50 57

A: Contour line draw

Q: 1. Complete the differential level notes shown below, perform the customary arithmetic check,…

A:

Q: Problem 3 Given in the tabulation below are the observed forward and backward bearings of an open…

A: To Determine Plot the traverse and adjust the forward and backward bearing of each course. Tabulate…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.