Oil (SG = 0.80) flows through a pipe AB 120 cm in diameter at 3 m/s and then passes through a pipe BC which is 150cm in diameter. At C the pipe forks. Branch CD is 80cm in diameter and carries one-third of the flow in AB. The velocity in branch CE is 2.5 m/s. Find the volume rate of flow in AB in m^3/s.Find the velocity in BC in m/s. Find the velocity in CD in m/s. Find the the diameter of CE in centimeters

Q: In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) =…

A:

Q: Determine the mass flow of the fluid if it has the velocity profile shown. The channel is 1.4 m…

A: There are many types of fluids like gas, liquid.it is having more functions like flexibility and…

Q: Two reservoirs A and B have elevations of 250 m and 100 m, respectively. The two tanks are connected…

A:

Q: A reservoir is filled with 4 m of water. A pump of area 0.009 m² at the bottom of the reservoir is…

A: ###Determination of flow rate Q through pump ##

Q: At two points 1 and 2 in a pipeline the velocities are Vand 2V, respectively. Both the points are at…

A: applying Bernoulli's theorem

Q: 12.7 The radial component of velocity of water leaving the cen- rifugal pump sketched in Fig. P12.7…

A: Given data:V2=90 ft/sVr2=45 ft/sN=3000 rpm

Q: A water jet of velocity 4.2 m/s and a cross-sectional area of 0.50 m2 strikes a curved vane, as…

A: Data given Flow velocity, V = 4.2 m/s Area of flow, A = 0.5 m2 Angle of split = 540 Solution Flow…

Q: at a high Reynolds number, for which the velocity profile is approximated by u Uy/R)/8, where U, is…

A: as per guidelines we need to answer only first question

Q: circular vessel 2 m. in diameter and 3 meters high as shown is filled with liquids A, B and C…

A: Given data,  Area of orifice = 0.09 m² Cd  = 0.6 Diameter of tank = 2 m Total height of tank = 3 m

Q: oil (SG = 0.88) dischargesfrom a pipe (D = 13 in.) through a sharp-crested, round orifice (diameter…

A:

Q: The flow through a rectangular channel (width in x and height in z) is nonuniform with a velocit…

A: We have to determine the expression for flow rate and average velocity using contants and we have to…

Q: In the figure, suppose that 0 = 30°, V1 = 100 ft/s and the stream is a jet of water with an initial…

A:

Q: Figure 4. The pitot tube is connected to the piezometric tube. The total head loss from point 1 to 2…

A:

Q: In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) =…

A:

Q: Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 cm?,…

A: At entrance -  A1 = 20cm2 ρ1 = 1878 kgmm3   At exit -  A2 = 10cm2 v2 = 249.5 cm3gv2 = 3048 cmmin

Q: Water flows with a flow rate of 0.6 cumec through an inclined pipe PQ of length 10 m lengt having a…

A: Flow rate = 0.6 cumecLength of pipe PQ = 10 mAngle = 30 degreePressure = 30 kN/m2We have to…

Q: A water reservoir of 300 (Height) x 300 (width) x 500 (depth) m has its free surface at 250 m above…

A: Height of reservoir = 300m Width = 300m Depth = 500m Dia of orifice = 500mm Coefficient of…

Q: The flow through a rectangular channel (width in x and height in z) is nonuniform with a velocity…

A:

Q: In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) =…

A:

Q: 5. Oil (S=0.92) is transported through the system as shown below. If the pressure head difference…

A: Given :

Q: H.W. I The velocity distribution for flow over a plate is given by c= 3 d - 2 d where c is the…

A:

Q: The velocity profile for the steady laminar flow of water through a 0.4-m-diameter pipe is defined…

A: IT IS GIVEN THAT -

Q: Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 cm2,…

A:

Q: Consider the incompressible flow of an ideal fluid having a density ρ = 1600 kg / m3 (figure 3). We…

A:

Q: 2xy, v = x² – y², is irrotational and incompressible, and determine its stream function p and…

A:

Q: having an impeller of 35 cm outside diameter rotates at al at exit and are 7 cm wide. The velocity…

A: Given:- diameter=35cm rotates =1000 rpm width=7cm velocity of radial flow=3m/sec velocity in suction…

Q: Consider a fully developed laminar flow of a fluid through a 8027 m long and 4 cm diamete horizontal…

A: length, l = 8027m diameter, d = 4 cm Pressure, P= 1252 kg/m3 i) Velocity  profile given,  U = 61-rR2…

Q: Water flows through a pipe AB 1.2 m diameter at 3 m/s and then passes through a pipe BC 1.5 m…

A: Given Data- Diameter of pipe AB DAB=1.2 m, Velocity of flow through AB VAB=3 m/s, Diameter of pipe…

Q: In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) =…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.