Oil is to flow through a pipe at 80°C, and for experimental purposes, the oil flow must be hydrodynamically and thermally fully developed laminar flow. If the pipe diameter is set at 2.5 cm, what is the minimum pipe length needed to ensure the flow conditions are met and the required pumping power to overcome the pressure loss in the pipe?

Oil is to flow through a pipe at 80°C, and for experimental purposes, the oil flow must be hydrodynamically and thermally fully developed laminar flow. If the pipe diameter is set at 2.5 cm, what is the minimum pipe length needed to ensure the flow conditions are met and the required pumping power to overcome the pressure loss in the pipe?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heavy oil with density of 912 kg/m^3; kinematic viscosity of 2.05 x 10^-4, is delivered yo an upper stortage tank from a supply tank whose oil level is 3.0 m. below the storage tank. The conveyance process is made by means of an 80% efficient pump through a pipe 500 m long and having a diameter of 5 cm. For discahrge of 4 liters/s, whay is the input power of the pump. Neglect mior losses. Choices: a.10.2 KW b.9.78 kW c.12.30 kW d.11.4 kW
An oil gusher shoots crude oil 23.0 m into the air through a pipe with a 0.100 m diameter. Neglecting air resistance but not the resistance of the pipe, and assuming laminar flow, calculate the pressure (in N/m2) at the entrance of the 45.0 m long vertical pipe. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) · s (or 1.00 Pa · s). Note that you must take into account the pressure due to the 45.0 m column of oil in the pipe.
Hot air (43 °C) at 1 atm flows into a circular plastic duct 50 m long at a rate of 0.2 m3/s. If the friction loss, hL, in the pipe does not exceed 6 m. Determine the diameter of the duct, the velocity of the fluid, and the Reynolds number.
What’s the answer for this please ?
It says my answer is partially correct. 264kPa is correct but it says 11.3m is not correct. What is the correct way to calculate this value?
An oil gusher shoots crude oil 23.0 m into the air through a pipe with a 0.100 m diameter. Neglecting air resistance but not the resistance of the pipe, and assuming laminar flow, calculate the pressure (in N/m2) at the entrance of the 45.0 m long vertical pipe. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) · s (or 1.00 Pa · s). Note that you must take into account the pressure due to the 45.0 m column of oil in the pipe.
Calculate the pressure differential and head loss in a 70-cm-diameter pipe using a 40-cm-diameter orifice meter if the water has a volumetric flow rate of 380 L/s, a density of 998 kg/m, and a dynamic viscosity of 1.002 x 10-3 kg/m-s.
What’s the answer for this please ?
At a speed of 0.2 m/s, light oil with a density of 880kg/m and a viscosity of 2.1cP is pumped from a huge oil tanker to a power plant's storage tank. The discharge point is 50m above the liquid level in the tanker, at the top of the storage tank. The pipeline is a 150mm smooth pipe with six typical 90° elbows and two gate valves that is 200 meters long (fully open). The atmosphere is vented from both the oil tanker and the storage tank. a. Calculate the pressure drop in J/kg along the pipeline. b. Calculate the pumping power (in kW) if the pump-motor set has a 65 percent efficiency.
Water flows through a measuring nozzle of 40mm diameter in a pipe of 75mm in diameter at a flow rate of 0.015 m3/s. Determine the pressure difference through the nozzle if the temperature is (a) 10°C, (b) 80°C.