Ulode Rectifier Configurations3.5.4 Questions & Answersa) In a half-wave rectifier, a diode will pass onlyhaltalternation of a sinewave.b) A half-wave rectifier can produce positive or negative pulsating DC, depending on theplaced in the circuit.which the diode isc) If a DC voltmeter measures 10V at the output of the half-wave rectifier, what is the amplitude of a sinewave?A de voltage measuve output y hald wave rectifjer oisVo = 1oVd) If a DC voltmeter measures -20V at the output of the half-wave rectifier, what is the amplitude of the sinewave?Yp VelT Theout put g hald Wave yectidier aus TT/2or) = 62.85e) What would be the reading of the DC voltmeter placed across the output of a half-wave rectifier if diode burnsshort?f) What would be the reading of the DC voltmeter placed across the output of a half-wave rectifier if diode burnsopen?no VOltage dvop acrossduving houd cyue Quddiod dawage excess heating of diode gets damage.Asthereout put D) be zero20ad ResiICstoncedue to ILO11 beAuthorization:declare that the findings presented inthis document are genuine results derived from authentic lab experiment which I haveconducted with my partner(s),1,This document does not contain results or findings copied from other students.Date:Lab Station No:3-11

Answered: Image /qna-images/answer/235e5213-217e-470b-b565-2675eed4c49e.jpg

ode Rectifier Configurations 3.5.4 Questions & Answers a) In a half-wave rectifier, a diode will pass only halt alternation of a sinewave. b) A half-wave rectifier can produce positive or negative pulsating DC, depending on the placed in the circuit. which the diode is c) If a DC voltmeter measures 10V at the output of the half-wave rectifier, what is the amplitude of a sinewave? output hald wave rectifier as A de voltage measuve Vo= 10r %3D d) If a DC voltmeter measures -20V at the output of the half-wave rectifier, what is the amplitude of the sinewave? Vp Vel The out put g hald wave vectiier as T/20V) = 6218 5

ode Rectifier Configurations 3.5.4 Questions & Answers a) In a half-wave rectifier, a diode will pass only halt alternation of a sinewave. b) A half-wave rectifier can produce positive or negative pulsating DC, depending on the placed in the circuit. which the diode is c) If a DC voltmeter measures 10V at the output of the half-wave rectifier, what is the amplitude of a sinewave? output hald wave rectifier as A de voltage measuve Vo= 10r %3D d) If a DC voltmeter measures -20V at the output of the half-wave rectifier, what is the amplitude of the sinewave? Vp Vel The out put g hald wave vectiier as T/20V) = 6218 5

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: 4. DC load voltage Ripple factor C.
Please help me answer thisa i promise to give high feedback plsss
I need the answer as soon as possible
In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The forward resistance of each diode is 252 and load resistance is 1.5KN. Calculate, i. Im ii. Idc iii. Pdc iv. Pac V.
Please answer alll subparts i will like....
A sine voltage trace displayed on a screen is shown in figure. The x axis is 1unit=40 ms and y axis is 1 unit=4 v; determine the frequency of the sine wave and plot the waveform if the same is applied to input of a full wave rectifier.
04: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10°t)] rms input signal has a loud resistor of 3.3k0. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLp) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de valtage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
write clean and descriptive
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
Part A, B and C