Obtain a formula for the strain energy U of the statically indeterminate circular bar shown in the figure. The bar has fixed supports at ends A and B and is loaded by torques 2T, and To at pointsC and D, respectively. (Assume that the shear modulus of elasticity is denoted G, and the polar moment of inertia is denoted Ip.)2ToToKU =

Answered: Image /qna-images/answer/7a68aee7-087f-4a68-bab9-2d7ec0d0cd3b.jpg

Obtain a formula for the strain energy U of the statically indeterminate circular bar shown in the figure. The bar has fixed supports at ends A and B and is loaded by torques 2To and To at points C and D, respectively. (Assume that the shear modulus of elasticity is denoted G, and the polar moment of inertia is denoted I,.) 27, To U =

Obtain a formula for the strain energy U of the statically indeterminate circular bar shown in the figure. The bar has fixed supports at ends A and B and is loaded by torques 2To and To at points C and D, respectively. (Assume that the shear modulus of elasticity is denoted G, and the polar moment of inertia is denoted I,.) 27, To U =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0.375 in. is subjected to internal pressure p = 375 psi. In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure). (Assume that the structures behave linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) (a) Determine the maximum tensile stress omay and the maximum in-plane shear stress Tmay in the wall of the cylinder. (Enter the magnitudes in ksi.) o, = ksi Tmax ksi (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T? (Enter the magnitude in kip-ft.) kip-ft (c) If T = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness (in inches)? in.
The cross-sectional dimensions of a beam are shown. The internal bending moment about the z centroidal axis is M₂ = +3.51 kip-ft. Assume b = 7.125 in., d = 5.25 in. and t = 0.75 in. Determine: (a) the maximum tension bending stress in the beam. (b) the maximum compression bending stress oc in the beam. Answers: (a) OT = i ) oc = i t b y K H ksi ksi.
Solve it correctly
Please include free body diagrams. Need asap
Within few minutes
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 2.6 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at C. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1m
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←
Flexure stress *Please answer in complete solution and draw the shear and moment diagram, Solve the Area moment of inertia*
n=8
The cross-sectional dimensions of the beam shown in the figure are a = 4.6 in., b = 5.7 in., d = 4.9 in., and t= 0.31 in. The interna bending moment about the z centroidal axis is M_= -4.45 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam.
The beam section given in the figure is under the influence of M = 5 kN.m bending moment. Section C and B ' Calculate the normal stresses that will occur at the points. E = 200 GPa. (N-A axis weight passes through the center.)