Ø35 R35 20 20 20 45 70 70 Ø40 120

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: I need these three parts answered, if you can not answer all three parts please leave it for another…

A: 6.Refer to the section B-B in the drawing. The cutting-plane line is the dotted line. Now, the view…

Q: 1. A 80mm long line AB has the end A at a distance of 20mm above HP and 40mm in front of V.P. The…

A: The front view, top view and side view of the specified question has been shown in the figure below.…

Q: Draw the front, Side and top

A: We need to draw three orthographic projection views.

Q: Draw the projections of the following points on the same ground line, keeping the distance between…

A: (a) Point C : 65 mm below HP on VP the point will be in the third and fourth quadrant. (b) Point D,…

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: A 100 mm by 150 mm rectangular plate QABC is deformed into the shape shown by the dashed lines in…

A: Given Data: H=100 mmB=150 mm   To Find: (a) Strain components εx, εy, γxy. (b) Principal strains…

Q: Draft and annotate the 2D sketch of cover using AutoCAD and mention all the dimensions. Colour the…

A:

Q: From the projected views obtain the isometric drawing.

A: According to the details provided in the question, there are three views of the first angle of…

Q: Find the mass of the trash can. Assume IPS, set before you begin to sketch the part. The material is…

A: Given Data A=34.84 Material: PE High Density Find Find the mass of the trash.

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: The front and top views of an object are shown below. Freehand sketch the section view of the front…

A: Given view are top view and front view

Q: GEOMETRY OF TECHNICAL DRAWING-TANGENCIES DRAW TANGENT TO CIRCLE AT PONT P AND TANGENT FROM Q TO…

A:

Q: For the given multiview projection, draw the corresponding isometric drawing. HAR 1

A:

Q: friction t

A: FIg:FBD Fr=μN∑Fy=0N=mgcosθ∑Fx=0μN=mgsinθμmgcosθ=mgsinθμ=tanθ

Q: what is the roles of other angles?I mean 45 and 30 degrees

A:

Q: Draw the sectional view of the figure

A: Draw the sectional view of the figure.

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Based on the given diagram, the following assumptions should be made before beginning the analysis.…

Q: correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying…

A: given:

Q: If a drawing has 6 fillets with radius (1/2 inch) for imperial units drawing, name one way that you…

A: If a drawing has 6 fillets with a radius (1/2 inch) for imperial units drawing, the one way that we…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.