O2. Two immiscible liquids of equal thickness h are being sheared between a fixed and a moving plate, as in Fig. 2. Gravity is neglected, and there is no variation with x. Find an expression for (i) the velocity at the interface and (ii) the shear stress in each fluid. Assume steady laminar flow. Fluid layer V. to P. P Fixed Fig. 1 Fig. 2

O2. Two immiscible liquids of equal thickness h are being sheared between a fixed and a moving plate, as in Fig. 2. Gravity is neglected, and there is no variation with x. Find an expression for (i) the velocity at the interface and (ii) the shear stress in each fluid. Assume steady laminar flow. Fluid layer V. to P. P Fixed Fig. 1 Fig. 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Consider a flow with the velocity profile given by the equation below. The fluid surface is located at y = 0. Here, U∞ is called the freestream velocity and 8 is called the boundary layer thickness. Calculate the boundary layer thickness at a point where the shear stress is 36 mPa if the freestream velocity is 40 m/s and the fluid's dynamic viscosity 1.81.105 Pa.s. U.. ( 2 (²) - (²) ²) u(y) = U∞o
Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N
Please don't use Artificial intelligence tools. Only Handwritten solution
1. Consider a flow with the velocity profile shown in the image below. Here, U is called the freestream velocity and & is called the boundary layer thickness. Calculate the shear stress acting on the fluid surface if the freestream velocity is 10 m/s, the boundary layer thickness is 2 mm, and the fluid's dynamic viscosity 10.³ Pa.s. fluid surface U.. 8
3.1 A cylindrical plug, 120mm long with a diameter of 95 mm, slides concentrically in a fixed cylinderwith an internal diameter of 95,2 mm. The radial clearance is filled with oil with a viscosity of 0.2 Pa.sCalculate the Force required to slide the plug along the cylinder at a speed of 5 m/s against the viscousresistance of the oil, the power lost due to the viscous resistance and the Kinematic viscosity of the oil ifits density is 850 kg/m 3 . A pressure intensifier is used in reverse deboost the pressure in a hydraulic system from 15MPa to7MPa. The volume of fluid required in the low pressure side is 700ml and the length of the stroke of thepiston is to be half the diameter of the low pressure piston. Calculate the diameters of the high-pressureand low pressure sides as well as the stroke length of the piston.
Problem 2 The apparatus sketched in the figure below serves as a viscometer i.e. it can be used to measure the viscosity of a liquid. In the drawing, D is a large reservoir containing a viscous liquid A and E is a cylindrical tube of radius R, open at both ends, surrounding and coaxial with B, which is a cylindrical "bob" of radius êR that is dragged up through the fluid by a frictionless pulley system (C) utilizing a weight W. Determine a design equation that relates the viscosity of the liquid to the geometry of the system and the weight W. Hint: you can assume that the length of the cylindrical tube is sufficiently long for the flow to reach steady state. W E D B
1-15. Analyze the flow between two plates of Fig. 1-15 by assuming the fluid is a de Waele power-law fluid as in Eq. (1-31a). Compute (a) the velocity profile u(y) with the power n as a parameter and (b) the velocity at the midpoint h/2 for n = 0.5, 1.0, and 2.0. Answer: (b) u = V/2 for all cases 1-16. Reneat that
Oil Coating: A long, continuous belt is pulled upwards through a chemical oil bath at velocity V0. The belt has rectangular cross-section and has length (L), width into the paper (W). The belt picks up a film of oil of thickness h, density ρ, and dynamic viscosity μ. Gravity g tends to make the oil drain down, but the movement of the belt keeps the fluid from running off completely. Assume fully developed, steady, laminar, incompressible and two-dimensional flow of oil to answer the following questions. Assume that no pressure gradient is needed in the vertical direction to drive the film flow. Also assume that the shear stress at the air-oil interface is zero (free shear condition). Assume no-slip condition for the fluid in contact with the moving belt. Justify any other assumptions you may make. Show all steps. (a) Derive an expression for the two-dimensional velocity field inside the oil film in terms of the known parameters. Clearly indicate your co-ordinates and origin. You must…
Consider the displacement of oil by water from a capillary tube with radius of 25 microns. Assume viscosities of both fluids are 1 cp, the interfacial tension= 30 mN/m, velocity= 0.4 m/day Calculate the pressure drop between downstream (oil side) and upstream (water side) of the tube?