O Determine the design tensile strength for the member and bearing type connections if A325 3/4-in standard bolts are used as shown below, threads are excluded for shear plane (Fy 36ksi and Fu=58ksi). Note: don't consider the slip critical connection in your calculations, E of steel is 29000ksi

O Determine the design tensile strength for the member and bearing type connections if A325 3/4-in standard bolts are used as shown below, threads are excluded for shear plane (Fy 36ksi and Fu=58ksi). Note: don't consider the slip critical connection in your calculations, E of steel is 29000ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4. An A992 WF steel section is used for the tension member shown in the figure. The bolts are 20mm…

A: A992 WF steel section, bolts are 20mm in diameter The WF section is to be connected to a 12mm-thick…

Q: snip

A: Calculate the gross area due to yielding. Ag=bt =5×12 =2.5 in2 Calculate the nominal…

Q: The bolted type connection will be used to assemble the given steel members. If PArmax = 8.36 t;…

Q: The plate shown is 8 in wide and 1/2 in thick. The bolts are 7/8 in. The smallest net area (An) of…

A: Given:- width of plate =8 inthickness of plate =1/2 inBolts diameter size = 7/8 inA36 plateTo…

Q: Result II. Construct the bending moment diagram of the following structure. Reviewer 8kN 6kN/m A 2m…

A: The algebraic sum of the vertical forces at any section of a beam to the right or left of the…

Q: connecte lameter bolts in each flange, as sho fFy 448 MPa, and Ae = 0.90An, compute the following.…

A: Given: C12x30 member 25 mm dia bolts fy=345 MPa, fu= 448 MPa Ae= 0.9 An

Q: B) The tension member shown in Figure is a W 16 × 40, and the steel is A992. The bolts are 3/4-inch…

Q: Check the bolted section of the given gusset plate connection assuming that the connection is done…

Q: For the splice connection shown in the figure, Compute the design strength based on shear and…

Q: A double-angle shape is shown in Figure 3.5. The steel is A36, and the holes are for…

A: Double angle section is shown in the figure above. Grade A36 steel is used. Diameter of bolts= 1/2…

Q: The bolt group shown in Figure P consists of 3⁄4inchdiameter, Group A bearingtype bolts in single…

A: Solution Given Data Diameter= 3/4 inch

Q: ¿A Tension member has used to resist load of 65 kips, and the shear stress on bolts is 15.9 kips.…

A: If two or more plates are to be joined then the bolts or welding is used. The applied shear stress…

Q: A straight steel bar is fastened to a gusset plate with three 3/4-in diameter ASTM A-307 bolts, as…

A: three 3/4-in diameter ASTM A-307 boltsbolt capacity in single shear = 7.95 kips plate capacity =…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Given- Properties of WT- 12×38Ag=11.2 in2y'=3.0 inbf=8.99 inA992 steel-fy=50 ksiFu=65 ksiLL=3DL

Q: The tension member shown in the figure contains holes for 3/4-in Ø bolts. At what spacing, s, will…

Q: A riveted connection is shown in the figure 3.26. A 25 mm diameter A 502, grade 2 rivets are used. A…

A: To compute:Tensile strength when shear stress of rivet governsTensile strength when bearing stress…

Q: Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in…

A: Answer A 325 group bolt 3/4 inch diameter bolt Plate 38 x 7 Plate 516 x 7 A 36 steel Live loadDead…

Q: An angle section ISA 120 x 100 x 10 is shown in the figure. The bolts used are of diameter 20 mm.…

A: Given data, For ISA 120x100x10 Diameter=20 mm Steel grade is Fe410

Q: Find the ava shown in the liameter bolts Use LRFI Use ASD 1 2) 3½" I

Q: Group A shp single Assume that the bearing strength is adequate and use an elastic analysis to…

A: Given To Find The maximum factored load that can be applied

Q: A single-angle tension member, an L4×4×3/8, liameter bolts as shown in the attached figure is…

A: L4x4x3/8 d= 7/8 in do= 1 in

Q: Determine the allowable tensile force P which can be appllied to the plates shown. The AISC…

A: Diameter of bolt, Thickness of plate, Width of plate, To find: Allowable tensile force.

Q: Determine the LRFD design tensile strength of the bolted connection shown. The angles are connected…

A: Given dia of bolt=16 mm fy =250 fx =405 diameter of hole=16+2 =18 mm

Q: Problem 6: Assume that the pieces making up the connection are adequate, and very stiff such that…

A: Service load, T=620 kNFrom the given service load, 25% is dead load and 75% is live loadGiven bolt…

Q: A double-angle shape is shown in the figure. The steel is A36, and the holes are for…

Q: The design strength , Pu based on gross area

Q: PROBLEM 1: CHECK THE ADEQUACY OF MEMBER BC WHOSE THICKNESS IS 14 mm, FIGURE : to

Q: The tension member shown in figure below is a PL ½ x 8 of A36 steel. The member is connected to a…

Q: A Channel Cóx13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using…

Q: Determine the design strength (LRFD)

A: Solution: calculate the strength of the plates as tension members Gross area Ag = 10(0.5) = 5 sq in…

Q: a. Determine the ultimate tensile strength of the tension member (channel) based on its gross area.…

A: For channel fu = 450MPa fy = 345MPa

Q: A PL % x7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1.…

A: Solution:

Q: he plate shown in the figure 2.19 has a thickness of 12 mm. Diameter of bolts is m. A 36 steel is…

A: t= 12 mmd= 16 mmFy = 248 MPa and Fu = 400 MPaThe standard nominal hole diameter of 16 mm bolts = 17…

Q: Use ASD to determine the width of the 5/8 inch thick A36 plate subjected to tension as shown below.…

A: ASD5/8 inch thick A36 platedead load, PD=85 kiplive load ,PL=80 kipTwo rows of 5/8 inch standard…

Q: miscellaneous channel MC 300 x 67 is bolted as shown on the figure 2.20 by a 0 mm diam. bolts. A 36…

A: Area of section, Depth, Thickness of web, Flange thickness, Width of flange, To find: (a)…

Q: Please show solutions on how to get the 0.5 and 1.0 value. The circle green in the figure. Civil…

A: The block shear failure consists of two failure surfaces The tension failure The shear failure The…

Q: The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with…

A: The given connection with dimensions as follows :

Q: (a) Check if the given connection follows the code provisions on spacing and edge distance limits.…

A: Answer (1) Check for Maximum and minimum spacing Minimum spacing As per AISC Manual 14 edition…

Q: Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The…

A: We know that Maximum factored LRFD tensile force capacity of the member is given by minimum of the…

Q: For the splice connection shown in the figure, a. Check all spacing and edge-distance…

Q: Situation 2: A WT 8x13 of A992 steel is used as a tension member, The connection is with 7/8-in,…

A: WT 8×13 of A992 Diameter = 78inch Fy=50 ksi Fu = 65 ksi Ubs = 1.0

Q: Problem 1. The tension member is a PL 6 x 1/2. It is connected to a 3/8-inch-thick gusset plate with…

A: Answer Given in the Below attachments

Question

01:) Determine the design tensile strength for the member and bearing type connections if
A325 3/4-in standard bolts are used as shown below, threads are excluded for shear
plane (Fy =36ksi and Fu=58ksi).
Note: don't consider the slip critical connection in your calculations, E of steel is
29000ksi
13 in
13 in
13 in
13 in
| 2 in
3 in 12 in
3 in
PL를 x 12
PL 1 x 12
P/2
P/2 E
PL x 12

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2 - Formulae and Calculations

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the effective net area of the tension member shown in the figure. 000 3"3" L6 X 6 X 1/2 %-in. bolts Ciri2 ENGINEERING Section STEEL DESIGN 1.67"
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 2" 3" 2" 1/2" thick Gusset Plate O 2" 3" 3" 2" 3/8" thick P
Please answer all the questions with a complete solution. thank you.
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
Please solve with complete detailed solution. Thank you.
A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use NSCP specifications and assume a double row of bolts with standardsize holes for a bearing type connection with threads excluded from the shear planes.Minimum tensile strength Fu = 552.93MPa. Assume diameter hole is 3mm bigger than thediameter of bolts. Allowable shear stress is Fv = 207MPa. Allowable bearing stress fb = 1.2Fu.Diameter of bolts is 19mm. Fy = 449.25MPa.(a) Compute the tensile capacity of the steel plates. (Max. Net Area = 0.85 of Gross Area)(b) Compute the number of 19mm diameter bolts to develop the full strength of the plates. Note: SHOW DRAWINGS AND SOLUTIONS.
PL 5/8 x 12 3/4-in-diameter bolts
PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
1. In the butt joint shown below, the 7/8-inch diameter boits are made of A325 steel with threads excluded from the shear piane and the plates are made of A36 steel. o of a Determine the bolt shear strength b) Determine the bearing strength of the plate ) Determine the tensile strength (both gross and net) of the plate d) What is the strength of the bolted connection?
PLEASE DOUBLE CHECK YOUR ANSWER Determine the maximum factored load that can be applied to the Tension member shown. The angle is ASTM A36. The diameter of the bolts is 1-in. CIVIL ENGINEERING STEEL DESIGN W12 x 16 4,-0.220 in -3.99 in 1=+=+=+= 3 in 3 in 3 in
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO