O 60 A 50 ohm lossless line connects a matched signal of 100 kHz to a load of 100 ohm. Load power is100 mW. Estimate:(i) Voltage reflection coefficient of load.(ii) VSWR of the load.(iii) Position of first Vmin and V,(iv) Impedance at Vmin andDefine the terms Attenuation loss, Reflection loss, Transmission loss, Return loss and Insertion loss.minVmay and values of Vmax and Vmin:max

Answered: Image /qna-images/answer/02d70cf7-380e-4511-b136-09e538c9e314.jpg

O 60 A 50 ohm lossless line connects a matched signal of 100 kHz to a load of 100 ohm. Load power is 100 mW. Estimate: (i) Voltage reflection coefficient of load. (ii) VSWR of the load. (ii) Position of first Vmin and Vmax (iv) Impedance at Vmin and Vmax and values of Vmax and V min Define the terms Attenuation loss, Reflection loss, Transmission loss, Return loss and Insertion loss.

O 60 A 50 ohm lossless line connects a matched signal of 100 kHz to a load of 100 ohm. Load power is 100 mW. Estimate: (i) Voltage reflection coefficient of load. (ii) VSWR of the load. (ii) Position of first Vmin and Vmax (iv) Impedance at Vmin and Vmax and values of Vmax and V min Define the terms Attenuation loss, Reflection loss, Transmission loss, Return loss and Insertion loss.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

help!!
How does the shielding of a cable affect its performance in terms of signal quality and interference resistance?
An unmodulated carrier is 680 Vp-p. Calculate the %m when its maximum p-p value reaches 650, 850 and 1050 V, and the minimum p-p value reaches 500, 300 and 50 V, respectively, upon modulation.
Attenuation, distortion, and noise contribute to transmission impairment. What is the solution, or how can these causes be improved?
Q#5:What is the need for frequency regulation in power system network?
A shunt generator supplies a 30kW load at 215V through cables of resistance, R = 110mn. If the field winding resistance, Rf =680 and the armature resistance, Ra =45mn. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
When the first element in any row of the Routh array is zero while rest ofthe row has at least one nonzero element ,we have to replace ‘S’ by 1/Z tofind the stability using Routh Hurwitz.True/ False
5-A lossless T.L. has Zo = 100 Q and is loaded by ZL. The VSWR = 2. The first two voltage minima are located at z= -10 and -35 Cm from the load where z = 0. Determine ZL.
Simplified or ideal equivalent circuit representation of transmission line at RF consists of: a. R and C b. R, L, C and G c. Rand G d. Land C Characteristic impedance at RF frequencies is purely: a. conductive b. resistive c. inductive d. capacitive Radiation loss of a transmission line: a. independent of frequency b. increases with frequency c. decreases with frequency d. increases at some frequency range and then decreases with frequency
TELECOMMUNICATIONS COURSE What is attenuation and how to reslove it?
Microwave
1. It is desired to match an 80 2 load to a 50 2 transmission line. Calculate: The value of a single resistor that can accomplish this over all frequencies. The values of two lossless (reactive) components that can accomplish this at a frequency of 400 MHz. The characteristic impedance of a quarter-wavelength transformer that can accomplish this at a given frequency.