question 7 You apply a voltage of 5 V across auniformly doped 1 mm long p-typesemiconductor bar and measure a currentdensity of 1 A/cm2. What is theconductivity of the semiconductor?O 0.02 S/cmO 5.0 Q-cmO 0.5 Q2-cmO 0.5 S/cm

Answered: Image /qna-images/answer/f976f729-c4cc-43f3-bfa6-ffa4c21a5524.jpg

Answered: O 0.02 S/cm

Engineering

Electrical Engineering

O 0.02 S/cm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 1:a) State why voltage control and cable stranding are necessary in powersystemsb) Briefly explain where and how the following state variables ofa power supply grid are controlled.i) Frequencyii) Active powerili) Reactive poweriv Voltage.
List and describe the different types of lighting classes available on the market. Discuss the different types of lights available for these classifications, say 5 key types of light bulb/ fitting per class. In addition, what types of lighting would be used in long car tunnels in comparison to a set of offices, or even streetlights? What factors would dictate the type of light used in each scenario? For the lights you think are most suitable for a tunnel and streetlight, discuss the construction of such lights and what materials need to be considered to make them suitable for their intended use.
Question 3 (a) Discuss and critique the law of electricity supply? (b). Explain with a diagram a Retail competition model of electricity market. (c). Explain effects when government has a bigger say in the operation of Public utilities.
TII 8.) 4 – 3 kW, 230 V and 3 – 8.5 kW, 230 V clothes dryers are to be placed in a building, the total VA loading to be used for these in the computation for service entrance conductor is: A. 24375 B. 37500 C. 33750 D. 36000
7.C. Which of the following statements about bonding is true?A. The joint or termination must offer opposition in the circuit for effective electrical connections.B. Effective bonding keeps impedance high if a fault should occur.C. The entire electrical safety circuit is only as good as its strongest bonded link.D. Bonding connections must endure high levels of fault current until overcurrent protective devices can operate. 7.b. Which of the following is required with a low-voltage incandescent lamp that's operating on a standardservice?A. PhosphorsB. Argon gasC. A step-down transformerD. A ballast 7.a. The ordering code for a large incandescent lamp provides information on theA. lamp power requirement, bulb type and size, and sometimes lamp color.B. lamp power requirement, bulb size and special features, and sometimes filament type.C. lamp voltage, bulb type and size, and sometimes lamp color.D. lamp voltage, bulb size and special features, and sometimes filament type.
What did you learn about the Republic Act No. 7832? "Anti-electricity and Electric Transmission Lines/ Materials Pilferage act of 1994." (150 words)
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
b) State six (6) examples of electrical hazard sources that can be found in home or office.
3.a. There may be installations where grounded conductors of different systems are installed within the sameraceway, cable, or box. In these cases, it's imperative that the system-grounded conductors remainA. spliced.B. disconnected.C. separated.D. buried.3.b. In dwelling units, the maximum allowable voltage between conductors that supply lighting fixtures isA. 220 V.B. 120 V.C. 115 V.D. 110 V.
6.a. The amount of short-circuit current that flows depends upon the amperes available at the source ofpower, the length of the circuit, and what other primary factor?A. The presence of a ground fault currentB. Proper installation of the branch circuitC. Presence of no previous damage to the electrical systemD. The size of the conductors and voltage at which they operate6.b. You're evaluating the components of a multioccupancy building that won't have an on-site employee. Tobe compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water-pump disconnect.
1. The maximum electrical trade size of intermediate conduit is____________. a. 125 mm b. 100 mm c. 24 mm d. 12 mm
2b) You are designing electronic circuit component for the Highway Authority to be used for vehicular traffic management at a junction because your best friend was knocked down at the junction due to lack of traffic management. What type of materials would you used?