Now consider that white noise (i.e., noise with a PSD that is constant with frequency) is introduced in the channel of the system described in the previous problem. An ideal low pass filter is used at the receiver input to reduce the noise as much as possible, while transmitting the desired signal. (a) By what factor should the cutoff frequency of the noise reduction filter be reduced in the 8-PAM case, compared to binary? (b) By what factor will the noise power at the decision circuit be reduced in the 8-PAM case? (c) By what factor will the noise amplitude at the decision circuit be reduced in the 8-PAM case? (d) To obtain the same symbol error rate for 8-PAM as for binary, how should the minimum level spacing for 8-PAM compare to binary? (e) If the 8-PAM level spacing is adjusted according to part (d) above, by what factor will the average signal power be increased in the 8-PAM case, compared to binary?

Now consider that white noise (i.e., noise with a PSD that is constant with frequency) is introduced in the channel of the system described in the previous problem. An ideal low pass filter is used at the receiver input to reduce the noise as much as possible, while transmitting the desired signal. (a) By what factor should the cutoff frequency of the noise reduction filter be reduced in the 8-PAM case, compared to binary? (b) By what factor will the noise power at the decision circuit be reduced in the 8-PAM case? (c) By what factor will the noise amplitude at the decision circuit be reduced in the 8-PAM case? (d) To obtain the same symbol error rate for 8-PAM as for binary, how should the minimum level spacing for 8-PAM compare to binary? (e) If the 8-PAM level spacing is adjusted according to part (d) above, by what factor will the average signal power be increased in the 8-PAM case, compared to binary?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. The terms “open-circuit", “short circuit" and “dead short" are used in speaking electricity. Answer the following questions about these three terms: a. What is the value of the resistance of an open circuit? b. What is the value of the resistance of a short circuit? c. What is meant by a “dead short"? 5 DDPasalo-Electrical Engineering Department COE MMSU EE 121: Electrical Circuits I 2. When a switch is open, is the resistance between its terminals high or low? ¸Low 3. What is the resistance of a closed switch (ideally)? 4. Using each of the methods shown in (a) and (b) below, calculate the value of the equivalent resistance of a combination of R1 = 5 ohms and R2 = 20 ohms connected in parallel a. Using the equation: 1/Requivalent = 1/R, + 1/R2 + 1/R3 = b. Using the equation: Requivalent = (R, x R2) / (R, + R2) = Ω
Please answer with explanation...
Define contactor
Explain the basic principles of voltage regulation in a power system.
A 4 pole10V, DC shunt motor operates on a load current 10A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. a) what would be the back emf?
A cylindrical 00 AWG copper wire is coated with NEMA class B insulation. The normal operating temperature of the wire is 40°C. What is the maximum current the wire can carry for 1 second without exceeding the NEMA temperature rating?
What code set standard for electrical installation work
TYPE OF APPLIANCES: AIRCONDITION what type of detectors are present in the schematic diagram of the appliance and kinldy discuss the function, and operation of the detector. Kindly include descriptions, schematic diagrams, technical specifications.
Write troubleshooting and maintenance of the three-phase separator ( show your answer in table)
As an electrical engineer how can you help preven the destruction of habitat of animals?
I need the answer as soon as possible
We are running 3 wires in an IMC to a control panel with a 150 amp circuit breaker disconnect in the control panel. The conduit is run 12 inches above the roof on a strut rack. The ambient air temperature is 88 degrees. This control panel feeds the #1 cooling fan. What sized ungrounded conductors do we need? All conductors have typeTHHN insulation. A #1 AWG B 100 Kcmil C #1/0 AWG D #10 AWG What sized IMC do we need? A 3/4" B 1 1/4" C 1" D 1 1/2"