NOTES: 1. RETAINER MUST WITHSTAND A FORCE OF 1.5 POUNDS IN THE OPPOSITE DIRECTION OF INSTALLATION AND NOT DISLODGE FROM THE - 2. CAVITY IDENTIFICATION REQUIRED. 3. PARTS TO BE PACKAGED IN SEALED PLASTIC BAGS AND FREE OF LOOSE DEBRIS. 4. LOT CONTROL REQUIRED. Unless Otherwise Specifed Tolerence Fraction 2 Place 3 Place Angle Do Not Scale Drawing Dimensions & Tolerance Are In Accordance With ASME Y14.5-1994 Using The Inch Sysfom Inch Metric -L015 (4.38] =L010 1.25 = 1.005 ja.13 VALVE MODULE. 545 SUB-GATE ON THIS SURFACE ONLY, NO PROTRUDING GATE VESTIGE PERMISSIBLE 339 -.050 R01. Ø.485 Ø.384 R.080 $218 4X.120 EQ. SPACED -(0.312) B NO FLASH PERMISSIBLE ON VALVE SEAT SURFACE SPEISPI FINISH NO.2 NO TOOL MARKS, KNIT LINES, PARTING LINES, ORANGE PEEL, FLOW LINES OR SURFACE IMPERFECTIONS ON SEAT- 348- 100 SECTION A-A R.005- SCALE 2:1 03 R (BLEND WITHØ.312) (136) R010 DETAIL C SCALE 20:1 8X R.015 -30 030 Ø.346 065 R.025 ALL PRRES AND COMPONEITS RUPRESEVTAD ON THIS DRANO srE PROpOCED WIHATERE THATS COMPATIILF WMALL GEND OF AUTOMOMEFUEL TPARTNURBERE DATE (051) 4X R005- PART NAME VALVE SEAT MODULE -2X R.015 O-RING GROOVE MUST BE FREE OF PARTING LINE FLASH MATERIAL: TORAWN BY Ø312 CHECKED BY: BCALE REV.R 4:1 SECTION B-B DWG SZE REL DATE ECO NO CHNO CHANGE iNO ----

Q: Sketch multi-views (front, top and right views) of the objects. The front view is from bottom-left…

A:

Q: Based on the front view and the right side profile view shown, use any projection method to find the…

A: Given Front and right view of the object To find Top and isometric view

Q: hand three planes of 'orthographic' projection (i.e., top, front, and side views). The dimensions of…

A:

Q: For the objects shown in isometric below, sketch the top, front, and right side views in the space…

A: Given: Draw front, top view and right side view of the given isometric view.

Q: Some necessary dimensions are dimensions that are missing. missing from the following 3-view…

A: According to the details provided in the three views of the drawing, there is a hole of 2 units in…

Q: Select the best top view (3rd angle projection) of the following drawing: O a Ob Od OC O None of the…

A:

Q: What is the difference between the terms "perspective projection" and "orthographic projection"?…

A: Explanation: Prospective projection: The perspective projection is a linear projection where three…

Q: 40 30 20 20 100

A: front view

Q: The three planes of 'orthographic' projection of an object are presented in Figure 1.1 below. Draw…

A: Draw the isometric block according to dimensions of the object as shown in the image:

Q: 5) If the lamp used is a LED lamp with an efficacy of 80 Lumen/Watt, what will be the power of the…

A:

Q: Given the Top and Front Orthographic views of an object, construct a One-point Perspective view in…

A:

Q: 3. On the part below, specify a geometric control to make the left surface in the front view…

A: The geometric control that we need to specify to make the left surface in the front view…

Q: COMPLETE THE HORIZONTAL VIEW OF LINE AB, THEN PROJECT A TRUE LENGTH VIEW OFF THE HORIZONTAL VIEW.…

A: Scale: 1=10Solution:

Q: Given the Top, Front and Right-side Orthographic views of an object, construct a Two-point…

A: Find  Two point perspective view of the object.

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.