NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part The two blocks shown are originally at rest. Neglect the masses of the pulleys and the effect of friction in the pulleys and between the blocks and the incline. Consider WA = 208 Ib and Wg = 308 Ib.

Q: Why are three views used to show the object?

A: As we all now everything around us can geometrically be defined in the cartesian coordinate system.

Q: What type of square has a blade that can be tilted to angular settings?

A: Diemaker's square has a blade that can be tilted to angular settings.

Q: What are the four movement that to be checked in a propeller loose blade

A: given; What are the four movement that to be checked in a propeller loose blade.

Q: Scale board

A:

Q: A 29/32 icnh hole must be enlarged to 59/64 inch to insert a bushing. How much wider than the…

A: To find out how much wider the hole will be after enlargement, we need to calculate the difference…

Q: x axis is wrong, please follow up thank you

A:

Q: What does the internal moment cause?

A: Internal moment are actually the moments due to the resisting forces generated when the cross…

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: What is a wet mounts?

A: A procedure that is performed in a laboratory to observe motile organisms in wet mounts. It is an…

Q: What are the basic differences between the dividing heads?

A: Given question: What are the basic differences between the dividing heads? The given question is…

Q: 6. What material is used 7. What is the unspecified tolerance for angular dimensions? 8. What is the…

A: Given figure  CHART DOWEL SPLIT TYPE  TO FIND :  7 .What is the unspecified tolerance for angular…

Q: What is the class of fit of a ½-20 UNF-2B thread?

A: The united thread series is classified into coarse threads, fine threads and extra fine threads. The…

Q: Multiple choice Which wheelbarrow shown is well designed

A: Given:

Q: What other engine components may have to be used to be machined if the cylinder heads are machined…

A: When machining the cylinder heads on a V-type engine, several other engine components may also need…

Q: QUESTION 2 If you have to precisely rotate your workpiece, which is held on an indexing head, by a…

A:

Q: Why Cross-rail attachment is required in shaper?

A: Cross rail attachment is required beacuse

Q: What is the output when a large gear drives a smaller gear ?

A: Given: What is the output when a large gear drives a smaller gear ?

Q: What are the simple connections?

A: Connections are the links used to various joint members in a structure or mechanism. It can connect…

Q: How are center holes drilled after layout ? Show the diagram of a method

A: When work is held and turned between centers, a center hole is required on each end of the work. It…

Q: What is the difference between a long position and a short position?

A: Long Position If an investor has long positions, it means that the investor has bought and owns…

Q: 16. If the chamfer lengths of Part No. 4005851 are at the low limit and the total dowel length at…

A: 16. If the chamfer lengths of Part No. 4005851 are at the low limit and the total dowel length at…

Q: What is the symmetrical axis?

A: Axis of symmetric.  Axis of Symmetry is a line that Split the figure into two symmetrical sections…

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: What is the process of locating the instantaneous center?

A:

Q: What is fitting mechanical

A: Fitting Process :- Assembling of various parts of the machine.

Q: What is the Axial Load?

A: The axial load is a force that acts along the centroidal or longitudinal axis of the system. If the…

Q: State and draw two methods used to mount cylinders?

A:

Q: What makes new gear special?

A: Given data:- Gear:-A gear is a mechanical device that connects two rotating shafts by transmitting…

Q: the main diference between the prick punch and center punch?

A: Prick punch is a mechanical tool, which is made up of steel and it is used to mark points on the…

Q: Which tool steel group would be the best for master gauges? D M P S

A: Given :-  Which tool steel group would be the best for master gauges? D M P S

Q: why the number of disk is 17-1?

A: Given data:- Number of disc in one shaft (n1)=8 discs Number of disc in another shaft (n2)=9 discs…

Q: What was the orginal size of the smallest outside diameter?

A: Data given-

Q: How many and what kinds of materials are needed to start a thread?

A: To start a thread, you typically need the following materials: Thread material: This can be made…

Q: What is a rotary axis?

A: Rotary tables and indexing heads are two specialized work holding devices that are added to the…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.