Note: Nyquist sampling rate is the minimum sampling frequency according to the sampling theorem In the sampler system shown below, the FT X(w) of the input signal x(t) is as shown below. If this signal is sampled using Nyquist sampling rate, then the spectrum Xs(@) of the sampled signal x-(t) is: X(@) 1 x(t) Sampler -100 n 100 я A. В. (@}sx* AA 100 hoo '-100n 100n - 400n 400n 800n w С. 4 Xs(@) D. Xs() NAKAA 100 100 -200n 200n 400x w -200n 200n 400n

Note: Nyquist sampling rate is the minimum sampling frequency according to the sampling theorem In the sampler system shown below, the FT X(w) of the input signal x(t) is as shown below. If this signal is sampled using Nyquist sampling rate, then the spectrum Xs(@) of the sampled signal x-(t) is: X(@) 1 x(t) Sampler -100 n 100 я A. В. (@}sx* AA 100 hoo '-100n 100n - 400n 400n 800n w С. 4 Xs(@) D. Xs() NAKAA 100 100 -200n 200n 400x w -200n 200n 400n

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Signal and system
i need the answer quickly
It is desired to sample and quantize the x(t)=sin(1000pit) sign. Since the sampling period is given as Ts=0.2*1000 and tau=0.1*1000 a) Plot the sign x(t) and the sampled sign xö(t), specifying values over a period. b) Draw the sign Xö(f) by specifying the values.
Please solve both parts correctly and handwritten and within an hour plz
Question 4
Question 10 Sample the input x (t) = et, given the sample period T = 0.5. What is the value of the sampled signal x[n] when n = 6? Specify your answer with THREE decimal digits of accuracy.
S 25% 9:15:09 202_650425_A1 (202_650425_Digital .. Consider the analog signal x(t)=2 sinc 200t + 3 sinc 500t. The sampling rate if it is sampled at 3.5 times Nyquist rate is Hint: sincx=sin(pi.x)/(pi.x) * (2 Points) 3.5 kHz None of these 1.75 kHz 1.4 kHz 4
The plot in the figure below shows the frequency content of a continuous signal. Determine the minimum sampling frequency, in Hertz, that can be used in order to ensure aliasing is avoided. (+-10% tolerance. Enter a numerical answer only) 30 25 20 Magnitude ✔ 10 5 0 0 0.2 Frequency Content of a Continuous Signal 0.4 0.6 1.2 0.8 1 Frequency (Hz) 1.4 1.6 1.8 2 #105
Q2 1) If the input signal of DSP Unit has sin wave configuration V=Vm sin X(3601) find the sampling frequency fs and time interval? 2) To the sampling frequency obtained from First division response fs when the general equation built in such: Y[n] X[n]. H[w] LO
I have a test please
As per sampling theorem: O a. Fs<2fmax O b. Fs22fmax O c. Fss2fmax O d. Fs>2fmax
Q4. The signal x(t) given by, x(t) = 1+2 sin(80nt) + 1.5 cos(300nt) + 0.5 cos(375t) + 0.7sin (815at) is applied to the following system LPF ADC Digital x(t) Fc=400 Hz FSAM? Processor a. Find the minimum sampling frequency that can be used by the Analog to Digital Converter, ADC, given that the Low Pass Filter, LPF, is ideal. Justify your answer. b. Each sample is then quantized (“measured") by comparing the amplitude of each sample to a standard set of 1024 levels. Determine the total number of bits generated in a six-minute interval. c. If the range of the ADC is ± 5 V, detrmine its resolution, A, and it's quantization error.