Follow the instructions. Typewritten for an upvote. No upvote for handwritten. PLEASE SKIP IF YOU HAVE ALREADY DONE THIS. Thank you 1.Calculate the value of the deflection under the concentrated loads (B and C) and slope atthe simple support (A). Use E = 200 GPa, I = 150 x 106mm4.Draw the shear and moment diagrams.25kN 30KN20 kN/m1mB 2m C 2m5m

Answered: Image /qna-images/answer/8d9e0454-839f-4db6-a652-ce6a354d8410.jpg

Answered: No upvote for handwritten. PLEASE SKIP…

Engineering

Civil Engineering

No upvote for handwritten. PLEASE SKIP IF YOU HAVE ALREADY DONE THIS. Thank you

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A beam 300 mm wide x 450 m deep is simply supported on a span of 6.8 m. Given: Superimposed…

Q: A consolidated-undrained test on a normally consolidate clay yield the following results: Confining…

A: The given data is shown below: Confining pressureσ3=155 kPaDeviator stress=180 kPaPore pressure=79…

Q: The activities, duration, and cost under normal and accelerated crashed conditions for a network…

Q: 10. A 100 m long earthwork volume for a proposed highway has a constant cross section of cut and…

Q: 15. Determine the required length of 175 mm x 325 mm cantilever beam that could carry a varying load…

Q: The single-angle tension member shown is made up of ASTM A36 with one line of 4-in. diameter bolts…

Q: A rectangular channel flowing normally full at a depth 1.40 m has base of width 2 m. The flow rate…

Q: A strechy material with a spring constant of 48 N/m is stretched 3.5 cm from its equilibrium length.…

A: Spring Constant, K= 48 N/m Stretched, δ= 3.5 cm = 0.035 m Find the resulting Spring Force, F = ?

Q: Determine the magnitude (lb) of the reaction at B when a = 21°, a 11.4 in, b = 14.96 in, y = 16.62…

Q: 1. Determine the following: If w₁-30 N/m and w₂ = 45 N/m, Est = 200 GPa and I = 17x106 mm². (BY…

A: Given A simply supported beam Required ¤A tc/a Deflection at B

Q: 1200 N 800 N/m 8m -8m- The vertical support reaction at fixed support

A: Free body diagram :

Q: 1. Determine the following: If w₁-5 kN/m and w2 = 7 kN/m, Est = 210 GPa, b = 50 mm and h = 150 mm.…

A: Solution-

Q: 13. Determine the safe concentrated load that the 175 mm x 375 mm simple beam could carry over a…

Q: The head developed by the centrifugal pump is 40 m while operating at the speed of 750 rpm. If the…

A: given- Head developed H=40 mNumber of revolutions N=750 rpmdischarge Q=50 cumec=50 m3/s

Q: the platform is brought up t

Q: A 2.75-m-diamter wood-stave pipe has 9 m3/s of water entering through a horizontal 30o reducing bend…

A: Solution-Diameter of the wood stave piped=2.75mDischarge of water=9m3/sAngle of bending θ=30°Unit…

Q: Q3 Block A movies on a roller along inclined surface and Connected to Block B by a link. Determine…

Q: Find the centroidal coordinates of the plane region shown:

A: This question is related to the Engineering Mechanics.

Q: A pentagonal prism with sides 50mm and axis 120mm is having one of the edges of its base on the…

Q: Determine the centroidal moment of inertia, Ixo and Iyo of the shaded figure

Q: sm find(X)=? Sm 1 *

A: step 1-

Q: H.W.6: A hollow circular cold-rolled bronze [G₁ = 6,500 ksi] tube (1) with an outside diameter of…

Q: Calculate the void ratio of a soil sample having porosity of 0.32 and a moisture content of 25%.

A: given- porosity n=0.32moisture content w=25%=0.25

Q: Q4: Determine the member end moments and reactions for the beam shown below using the…

Q: F. A 2 km long pipe of 0.2 m diameter connects two reservoirs. The difference between water levels…

Q: A square column foundation with base of 1.40 m is shown in the figure. It carries an axial load of…

Q: consists of a H.W.7: The composite shaft shown in Figure solid brass segment (1) and a solid…

Q: Q- What is the representative fraction for a scale of 10 cm=20 km? Represent the answer in the form…

A: Given data- given scale10 cm=20 kmTo Find-Representative fraction RF

Q: de the comm

A: Rainfall and run-off are the two main factors that influence storm flows. It is vital to use…

Q: Problem 1.2 Two water tanks are connected to each other through a mercury manometer with inclined…

A: Answer We are given Pressure at A = 20 Kpa Pressure at B = 40 Kpa Density of water = 1000 Kg/m3…

Q: H Нд KANNANCESCORT RETRE water D perfect h=28cm D=48 mm d=0,8 b Q-?; H-? build prezometric line Parm

Q: Three pipes of diameters 0.4m, 0.2m and 0.3m of lengths of 400m, 200m, and 300m, respectively, are…

Q: 1.80 1.80 1.80 3 kN A B -1.80- с D -1.50-1 K -1.80- F P3= 16 KN. G P1 H P2 P3

A: Determine support reactions: HH=10+13+16=39 kN Take Moment @ A, (10×5.4)+(13×3.6)+(16×1.8)=(VH×5.1)…

Q: Consider a non-uniform 10m long cantilever beam, with flexural rigidity of 300 kN/m if 0≤x < 5 x+15…

A: L = 10 m cantilever beam, We know that the deflection equation is given by…

Q: The hydraulic gradient for quicksand condition is equal to 1.26 with a void ratio of 0.58. The moist…

Q: Find the value of work done in displacing a object by 8 m. The required force to displace is 12.5 N

A: Given data : The value of force applied F=12.5 N The value of displacement d=8 m Required : Work…

Q: assume the section and use transformed - Area method to compute their flexural stresses for the…

Q: A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown…

Q: A tank is shaped like a vertical cylinder; it initially contains water to a depth of 9 ft, and a…

Q: A consolidated-undrained test on a normally consolidate clay yield the following results: Confining…

A: This question is from Geotechnical Engineering.

Q: ered in the design

A: A VIP is a vented improved pit latrine with a vertical vent pipe that is similar to a single pit…

Q: A block of birch wood floats in oil with 86.5% of its volume submerged. What is the density of the…

A: Asked: To determine the density of the oil in which the given birch is submerged. Given: Percent…

Q: A moist soil sample having a volume of 1.51 m3 has a total mass of 2,360 kg. Specific gravity of…

A: Volume of Soil = 1.51m3 Total mass of Soil = 2360 kg Specific Gravity of Soil = 2.67 Water Content…

Q: SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in…

A: Truss is formed by members connected through smooth pin joint , members take axial load only

Q: Barometric Pressure is 29.89 in Hg. Convert the following a. 68 psig to mm Hg absolute b. 100 kPag…

A: Given:Barometric pressure is 29.89 in Hg

Q: A moist soil sample having a volume of 1.58 m³ has a total mass of 2,323 kg. Specific gravity of…

Q: Two tanks are connected with the three pipes of length 2 m, 3 m, and 4 m and diameters 20 cm, 30 cm,…

Q: An ASTM indicator of workability when evaluating freshly mixed Portland cement concrete. Choices:…

A: ASTM C143: Slump is a measure of the consistency of a sample of concrete. It can help give an idea…

Q: Q3 Block A moves on a roller along inclined surface and Connected to Block B by a link. Determine…

Q: For cantilever shown below: (BY DOUBLE INTEGRATION METHOD) W₁ kip/ ft W₂ kip/ ft B 5 ft 2 ft 3 ft If…

Question

100%

Follow the instructions. Typewritten for an upvote. No upvote for handwritten. PLEASE SKIP IF YOU HAVE ALREADY DONE THIS. Thank you

1.Calculate the value of the deflection under the concentrated loads (B and C) and slope at
the simple support (A). Use E = 200 GPa, I = 150 x 106mm4.
Draw the shear and moment diagrams.
25kN 30KN
20 kN/m
1mB 2m C 2m
5m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 23 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2/Find the vertical deflection of joint c (use Unit Load). E=200*10³ kN/mm², A-301 mm² ,short (AB)=5mm 4m B 3m C 10kN
H.W3 Determine the slope and deflection of end A of the cantilevered beam. E = 200 GPa and I = 65.0(106) mm². 10 KN -3 m 10 kN-m
Determine the shear (in kN) in member AB using Portal Method. Input the magnitude only. P=50KN A C E=200GPA 3.5m |=100(10°)mmª A=9000mm2 F D E 5m 5m
4. Byusing Area Moment Method, Determine the deflection 3mto the left of rollersupport. A 30 kN/m B 55 KN 9m El = constant E = 200 GPa I=830 x 106 mm4 (a) Real Beam -3 m-
A restrained beam is loaded as shown below. a. b. | Determine the end moment at wall A (MA). Determine the deflection at point C. IM 40KN IM 27kx/m 2M
. Show the Shear-Moment Diagram. (Use equation method) 42 3⁰° R₁ 42 Wo F7
PART 2: For the given Statically Determinate Beams, Perform the following. Write the Shear and Moment Equations b. Draw the Shear and Moment Diagrams а. С. Draw the Elastic Curve d. Indicate where the Point/s of Zero Shear е. Indicate where the Point/s of Contraflexure 75 kN 200 kN-m P D A B 4 m- -4 m 4 m
USE SLOPE DEFLECTION METHOD Given the indeterminate beam, find the moment at Bin span BC Mac in kNm. EI is constant 10 KN 5KN/m Sm 2m O Zoom mage O -881 O -11225 -633 -3.995
From the given beam loaded has shown; Determine the deflection at point D in mm. Using Moment Area Method. Let P =37 kN. EI = 14220kNm2 | 2P D B A - 2P 3.0 m 1.5 m 1.5 m Moment diagram by Parts 3P -3P Deflection curve diagram
The beam is supported by a pin at A, a spring having a stiffness at B, and a roller at C. Determine the deflection at B. EI is 40788045.2 kNm². a. 1.50 mm b. 0.404 mm c. 1.40 mm d. 0.912 mm
6. The beam shown supports a 15 kN concentrated load at the free end and another 15 kN at point C, determine the slope at B and the deflection at point C. Use E = 200 GPa and 1=9 x 107 mm¹. Use conjugate beam method 15 kN CS Scanned with CamScanner a A -2.0 m -21 b -4.0 m 15 kN c -31- -4.0 m
PART 2: For the given Statically Determinate Beams, Perform the following. Write the Shear and Moment Equations b. Draw the Shear and Moment Diagrams а. С. Draw the Elastic Curve d. Indicate where the Point/s of Zero Shear e. Indicate where the Point/s of Contraflexure 20 kN 20 kN D B C to -3 m· -3 m- -3 m-