Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum shear stress at point A on the cross section of the bracket at section a-a. Calculated for you: I,= 0.79948 in“, cross sectional area is 0.875 in². 0.5 in. 025 in. so0 0.25 in----0.25 in. Is in'1.5 in. L. Section a-a 6 in 12 in.

Q: 1. Compute the stress (ksi) in each member of the Warren truss as shown in the figure. Indicate…

A:

Q: Q3: The shaft consists of three concentric tubes, each made from the same material and having inner…

A: Handwriting.jpg

Q: Calculate the pressure difference between the two points РА- Рв A B oil S.G 0.91 y 10cm Hg

A: To determine the difference of pressures at points A and B

Q: At a given instant of time, the position r and velocity v of a satellite in the geocentric…

A: To Find : The orbital elements. Given : The geocentric equatorial frame are

Q: 6- Precipitates are Two dimensions in nanoscale Nanoparticles O true O false 7-APF for a…

A: Solution.jpg

Q: A Venturi meter with a 15 cm I.D. at inlet and 10 cm I.D. at throat is laid with its axis horizontal…

A:

Q: 2. Determine the force P required to maintain the 100-kg engine in the position for which 0 = 45°.…

A:

Q: Q1: An Otto cycle with air as the working fluid has a compression ratio of 8.2. Under cold air…

A:

Q: Q2/ An ideal gas, Cp= (2) R and Cv=R, undergoes the following mechanically reversible changes in…

A:

Q: 4) The workpiece material is copper alloy. Assume that D=220 mm, w = 40 mm, 1= 550 mm, d=2 mm, v=1…

A: Given Data The diameter is:D=220 mm The width of cut is:w=40 mm The length of the cut is:l=550 mm…

Q: Q (2): Knowing F2=420 N, F3=630 N. and the magnitude of the resultant force acting on the bracket is…

A:

Q: Q5/ An existing process consists of two steps: (a) One mole of air at T1=900k and p1= 3 bar is…

A:

Q: 550 m/s ÇLAI At a given instant the jet plane nas a spee 70 a = 50 m/s? and an acceleration of 50…

A:

Q: Ex/ Determine the magnitude and direction of the resultant of the forces shown. 150N 200N 30

A:

Q: Water flowing with a velocity of V₁ in a pipe is turned to flow in the x- direction. What is the…

A:

Q: Q1:Asteeile sPeerimen with f20mm Sabjected to a load 125 kN and agagtongth 135mmis observed A…

A: Given, Initial Diameter d1 = 20 mm Initial Length L1 = 120 mm Load P =125 kN Final Length L = 135 mm…

Q: 7 8 10 15 20 25 10 15 20 3. 3 6. 8 9 8 9 2, 4. 16 5n 4. 4.

A: Hi and thank you for the questions. We are authorized to answer one question at a time, since you…

Q: Rigid bars AB and BCD are supported by pins A and D and by a steel rod at C. There is a roller E =…

A:

Q: 12.17 Boxes A and B are at rest on a conveyor belt that is initially at rest. The belt is suddenly…

A:

Q: An aluminium pipe is rigidly clamped to the face of a concrete building. On a hot day the face of…

A:

Q: Given the venturi meter and the two pressure is shown, calculate the mass flowrate of water in the…

A:

Q: Q1/ An ideal gas, Cp-R and Cv=R, is changed from p₁=1 bar and v₁=10m³ to P2 = 10 bar and v₂ = 1m³ by…

A:

Q: Draw the Shear and Moment Diagram for the given loadings below

A:

Q: Q2: Can cBN be used in honing stick in single layer configuration?

A: Yes, CBN can be used in honing stick in single layer configuration. Honing stick with CBN makes…

Q: 17) Tension is the only type of stress applied in forming process. 18) rolling mill type are…

A: 17. Deep drawing  18. Cluster mill and four high mills  19. Sheet bending  20. Butt  21. High  22.…

Q: E : Consider a large plan wall of thickness L=0.06 m and thermal conductivity k-1.2 W/m °C in space.…

A: Given that ε=0.85 , solar absorptivity(α)=0.26 T1=300K  ,  L=0.06m  ,  k=1.2  , qsolar=800W/m2 outer…

Q: Q2. The system shown below is in equilibrium. Find the reactions at A (hinge support) and the force…

A: find the reaction at point A and force at B.

Q: 12-101. A projectile is fired from the platform at B. The shooter fires his gun from poin A at an…

A: Given   Angle = 30o   Horizontal distance, x = 20 m  Vertical distance, y = 10 m Find   Speed of the…

Q: If the temperature difference across each radiator is 15 °C, the mass flow rate of water in pipe LM…

A: Correct answer is option c 0.111 kg/ sec

Q: Q1/The system shown in figure (1) consists of a spring of constant (k) and that the spring is…

A: Understand that the given string is inextensible thus, the displacement, velocity and acceleration…

Q: Determine the resultant moment of * the forces shown about point A 200 N 60 N 30% 30° TOON 0.75 m…

A:

Q: 1. During a ground test with both main and tail rotors in steady operation, a 400 N aerodynamic…

A: Given   Force, F = 400 N Distance, d = 6 m Find  Force couple system, C

Q: The boy at A attempts to thrown aball over the roof of a barn such that it launched at an angle…

A: Angle, θA= 40∘ Horizontal distance from the point of throw and the axis passing through point C=…

Q: Th

A: Given-Information:-  Aramid Fibers, 45 % Polycarbonate, 55 %Modulus of elasticityTensile…

Q: Q1: A missile starting from rest travels along a straight track and for 10 s has an acceleration as…

A:

Q: What are the differences between hydraulic vise and screw vise

A:

Q: 3. You are working on your 1965 Mustang and have pulled the original Thriftpower 16 engine weighing…

A:

Q: Draw the shear force and bending moment diagrams for the loaded beams shown? Explain breifly why the…

A:

Q: Use basic drawing instruments (pencil, scale, protractor, compass, etc). Briefly explain with the…

A: Extrusion: It is used to make the base part of the model. It is used to add bosses and features to a…

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.