need to find the following items: 1) the current supplied by the source 2)the impedance seen at the supply (High voltage side) 3)the power dissipated by the tube.

Q: What are Diagram,Construction, Operation, Advantages and Disadvantages of Vacuum Circuit Breaker.…

A: It is asked to to draw the diagram and explain the construction, operation, advantages and…

Q: what is the scheme of the conductivity electrode

A: The conductivity electrode is a critical component in measuring the conductivity of a solution,…

Q: how to make an electromagent?

A: Electromagnet are the materials which can generate magnetic field around them, when the electric…

Q: Determine the current flowing through the LED. (assuming its forward voltage is 2.1 volts) * A D1 D2…

A:

Q: Explain how the resistances of common metallic conductors vary with temperature.

A: What is resistances in a material? Obstacle to the flow of electron in a material is called the…

Q: What are the main auxiliary components used together with a linear fluorescent lamp and what are…

A:

Q: Solve the circuit shown when V₁ = 10V, V₂ = 5V, R = 1990 when the diodes have linear models with Vj…

A: In this questionWe need to determine the current in the resistance R as shown the circuit. Given…

Q: What documentation is needed before work on, near or associated with high voltage is carried out?

A: Work near or associated with high voltage should be done carefully and under supervision.

Q: the resistivity of annealed copper and aluminum?

A: copper is one of the oldest known materials. Its ductility and electrical conductivity were…

Q: Is ohm law applicable to semiconductor, insulator. Give reasons?

A: Ohm's law is a law that is associated with voltage , current and resistance. It states that the…

Q: What is the unit of Luminous flux, Illumination, Solid angle, Luminance and Lamp efficiency ??

A: When light falls on any surface this phenomena is called as Illumination. Where Light is the cause…

Q: Q.1 Write about the operation of tungsten filament lamp – vacuum type?

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Discuss the important of guard-wire method in a high resistance measurement.

A: Solution: Guard wire is used to deflect the surface leakage current in high resistance measurement…

Q: I am handling a junction boxes where we are having pre-charge circuit, why is it being used here?

A: A pre-charge circuit is commonly used in electrical systems, especially those involving high-power…

Q: 3.Explain the positive clipping operation with circuit diagram and Waveforms.

A:

Q: What is Pre charge circuit and what is the use of it inside the junction boxes?

A: A pre-charge circuit is an electronic circuit used to gradually apply voltage to a circuit or system…

Q: Describe how you could investigate how the pd through a filament lamp affects its current.

A: In the case of the filament bulb, the current may not increase at a speedy rate compared to the…

Q: Define corrosion and also explain primary and secondary briefly explanation? step by step

A: The corrosion can be referred as the process by which the metal conductors loose their properties…

Q: What is the (Methods) to calculate the value of resistance?? and how we can using the multimeter…

A:

Q: Draw equivalent circuit of PV cell with explanation and labelling in details

A: PV cell:  It stands for Photo voltaic cell . It is also called as solar cell. It is a device which…

Q: What Are The Type Of Measurement Of High Direct-Current Voltages and explain one of them ? Compare…

A:

Q: What is the procedure for Waste Vegetable Treatment to produce electricity.

A:

Q: Write the report on “Increase of fluorescent lamp and power factor”

A: Fluorescent lamps: Fluorescent lamps, often known as fluorescent tubes, are low-pressure…

Q: What is the device that is used to convert nonelectrical signal to analog electrical signal…

A: Device which is used to convert non electrical signals to electrical signals are called transducers…

Q: Explain and elaborate the difference between zener and avalanche breakdown voltage

A: The zener breakdown and avalanche breakdown voltage of the zener diode need to be briefed.

Q: Provide an assessment of what the FIVE (5) performance measures mean for Flame Electrical.

A: Operations management may be described as the area in which managers are tasked with designing and…

Q: What will be the unit of hole mobility

A: The solution is provided in the following section:

Q: Deflection of an electron beam by electric field Follow the method to calculate how the voltage…

A: CRT tube In this type of tube, electron current flows through a gas. (generally, a noble gas is used…

Q: Question: A 1-phase full bridge inverter can operate in load commutation mode in case load consists…

A: A single phase bridge inverter can operate in load commutation mode in case load consists of  1.…

Q: explain the difference between valance electrons in conductors and insulators.

A: valance electrons in conductors and insulators.

Q: Why n - type impurities are called as Donor impurities?

A: => When a small amount of pentavalent impurity, such as arsenic, antimony, bismuth or phosphorus…

Q: Explain the working of fluorescent tube with the help of circuit diagram giving the function of…

A: Fluorescent Tube It is gas-discharge mercury-vapor low-pressure lamp that utilizes fluorescence to…

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.