please answer in 20 mins A man is trying to pull a 576 N crate C, initially at rest on the road, with a rope attached at point A using a force of P = 240N. The coefficients of non-slidingand sliding friction between the road and the crate are μs = 0.5 and μ = 0.4, respectively. The crate is 1.2 m high and 0.8 - m wide.34ABbChWhich of the following is TRUE about crate C?Crate C is impending to tip onlyCrate C is impending to slide onlyCrate is already slidingCrate C is not moving♦

nd sliding friction between the road and the crate are μ = 0.5 and μ = 0.4, respectively. The crate is 1.2 3 4 A B b C h m high an Which of the following is TRUE about crate C? Crate C is impending to tip only Crate C is impending to slide only Crate is already sliding Crate C is not moving

nd sliding friction between the road and the crate are μ = 0.5 and μ = 0.4, respectively. The crate is 1.2 3 4 A B b C h m high an Which of the following is TRUE about crate C? Crate C is impending to tip only Crate C is impending to slide only Crate is already sliding Crate C is not moving

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are given a metal rod, cut to a length of 12 in plus/minus .25in. Then you need to cut off 2 in with an accuracy of plus/minus .25 tolerance. You end up with a 10 in rod but what is the tolerance? (hint: rely on the basic principle of tolerance
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
How did you get 4/5 and 3/5?
*NOTE ON INSTRTUCTUONS AND HINTS
Please answer 3, 4, 5, 6, 8, 9, 10, 12 1 is 0, 2 is 0, 7 is point A, 11 is 2. I included a picture of someone who solved but they were mostly incorrect. Please do not answer if the solution set I provided with the incorrect answers was you. I appreciate the attempt, but the solutions for 3, 4, 5, 6, 8, 9, 10, 12 were marked wrong, so unless you have different answers, please do not submit the same incorrect solution set. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the mass center G is set as the origin (datum), the gravitational…
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
Hi, Could you please help with this question, if you need to take more credits then please feel free. showing working out if possible too please, Thank you
Show all work and steps please
Please only answer number 8
Solidworks
Create a list of operations for the blueprint provided below. The list of operations must be in chronological order. • All units are in millimeters• Drill depth: 15mm• Raw material dimension: o Body: 65mm longo Cap: 30mm long• Note: Some corners are chamfered so don’t forget to include it in operations
Can someone please help to solve this question following the directions and showing neat work and formulas and drawing all needed diagrams. PLEASE AND THANK YOU!!!