n this way, ignore the weight of the cover. The circular cover is 4m wide and is hinged from A. Determine the component of the hydrostatic pressure force on the cover and determine the force F by assuming that the cover is in balance.

Q: Determine the hydrostatic force in kN acting on an isosceles triangular plate of base 6.45 m and…

A:

Q: 3. A 3 rectangular gate is hinged at the top edge A and is restrained by a fixed ridge at B.…

A: Calculated the hydrostatic force exerted on the gate  and the location of line of action of force.

Q: The figure shows a high-pressure hand pump used for boosting oil pressure in a hydraulic line. When…

A: The hand pump's principle is to create low pressure in order to pull subsurface water. Two or more…

Q: Calculate the pressure exerted by water on the hull of a submarine that is cruising at a depth of…

A: Depth, h = 500 ft = 152.4 m Density of ocean water = 1025 kg/m3

Q: Gate AB has a width of 2ft and its weight is negligible. Water density is 62.4 psf. Determine…

A: The width of gate AB w=2 ft The water density =62.4 psf

Q: 3. The given triangular AB gate is hinged at A. Determine the weight of the gate that is required to…

A:

Q: 1. The tank is fined with water. Determine the resultant force acting on the triangular plate A and…

A:

Q: A square lamina (each side equal to 2m) is submerged vertically in water such that the upper edge of…

A: Given Data

Q: a force is 1.6 kN is applied uniformly on piston of 8 cm diameter. determine the pressure on the…

A: Given data: force = 1.6 KN = 1.6 * 103 N Diameter = 8 cm = 0.08 m to find: Pressure on the piston =…

Q: watersurface. 1-3 m hinged gate P 3 m

A:

Q: A Cylnder of Im n diamder is made with material of relative donsity o5. It is moored in fresh water…

A:

Q: 4. Find the force on the following triangular submerged plate in water and location of its center of…

A: Introduction: The pressure produced by a fluid at equilibrium owing to gravity at a specific place…

Q: The water-gate articulated in point B and inclined at an alfa angle to the horizontal retains an H…

A: Given:Depth of water, H=4.0 mInclination angle of the gate with the horizontal, α=60oWidth of the…

Q: The Hoover Dam is 221 m tall and 379 m wide. Approximating it as a flat plate, determine the…

A:

Q: The corner plate of the ship's hull is bent at a radius of 1.5 meters, following the arc of a…

A:

Q: 3. Determine the vertical and horizontal forces on the cylinder shown in Fig. below. The cylinder is…

A:

Q: The gate shown is hinged at (0) contains water on one side and oil on the other. What force (F) is…

A: The expression for the area of the gate on the water side can be written as, A1=0.7 m2.8 m=1.96 m2…

Q: ir pressure in the top of the bottle is olume of pon remains at 2 liters

A:

Q: A square plate of surface area 9.2 square meters is held vertically in water. Determine the total…

A:

Q: An isosceles triangle gate in a wall is hinged at location A. Determine the magnitude of force FH…

A: The objective of the question is to determine the magnitude of force FH required to hold the gate…

Q: The gate shown below has a homogeneous depth into the page of 5 meters. Label all parameters and…

A: Given:The width is  the height is the density of water is

Q: The 3 × 4-m side of an open tank is hinged at its bottom A and is held in place by a thin rod BC.…

A: Given that the area of the plate AB is 12 m2 Let the tension ‘T’ in the rod BC, Now, make a Free…

Q: Watersurface. -3 m hinged. gate P 3 m

A: Given data:-specific weight of water, ω=9810N/m3weight of gate, W=800NNow,length of the gate,…

Q: . A closed tank is filled with water and has a clear hemi- spherical observation dome with diameter…

A: Givend=4ft=4×0.3048=1.2192mh1=5ft=5×0.3048=1.524mh2=1.5ft=1.5×0.3048=0.4572mh3=2ft=2×0.3048=0.6096mS…

Q: 5-109 A square viewing window is located in a large wa- ter tank as shown in Fig. P5-109. Determine…

A: Draw a diagram for the problem and show the cross-section of the square window. Here, C is the…

Q: 4. A sliding gate of height 14mand width 28lies in vertical plane that weighs 25AN. Determine the…

A: Given: Height of the gate→h=1.4 m Width of the gate→b=2.8 m And wieght of the plate→W=25 KN because…

Q: Determine the ration between the forces on the lower area and the upper area if its divided by the…

A:

Q: If the plate is replaced with a vertical triangular plate (base = 5ft and height = 12ft) where its…

A: Dimension of the triangular plate,base, B=5 ftH=12 ftbase is submerged  by 12 ft below the water…

Q: 1.5 m H F A 4.2m water 30°

A:

Q: A circular cone has a diameter of 100mm and height of 200mm. It was weighed and the result was 1.4N.…

A:

Q: The vessel shown below contains linseed oil at 77° F. One side of the vessel contains a spout which…

A:

Q: If the base of the triangles is 1m below the surface of 20 degrees Celsius of water, determine the…

A: Givenx=1mb=4mh=3m

Q: The gate shown is hinged through a point A and is restrained from opening by a fixed ridge at point…

A:

Q: 3. A fine (thin) ring with a radius 50 mm is being pulled from the surface of water. If the ring has…

A: Given Data The radius of the ring is: r=50 mm=0.05 m Mass of the ring is: m=0.1 g=1×10-4 kg The…

Q: The Centre of the pressure of a plane surface is immersed in a liquid equal to the weight of the…

A:

Q: The uniform 20 Mg triangular gate is 1.5 m wide at B and is hinged at A. The gate rests on a smooth…

A: When a surface is submerged in a fluid, the fluid exerts forces on the surface. These forces must be…

Q: The gate shown in Figure 5 has a mass of 225 kg/m normal to the screen/page and is normal to the…

A:

Q: The image below shows a typical laboratory equipment found in some universities. The goal is to…

A: Given: To be explained: Do the hydrostatic forces need to be taken into consideration if we take…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.