n-Octane type fuel is burned in the boiler of a power plant, which is fed into the combustion chamber at a rate of 7.6 [kg/s] The steam flows in the boiler at a rate of 87.45 [kg/s]. a. Calculate the air flow in order for the combustion in the boiler to be stoichiometric. b. Calculate the air flow if the combustion occurs with an oxygen excess of 400%

n-Octane type fuel is burned in the boiler of a power plant, which is fed into the combustion chamber at a rate of 7.6 [kg/s] The steam flows in the boiler at a rate of 87.45 [kg/s]. a. Calculate the air flow in order for the combustion in the boiler to be stoichiometric. b. Calculate the air flow if the combustion occurs with an oxygen excess of 400%

Chemical Principles in the Laboratory

11th Edition

ISBN:9781305264434

Author:Emil Slowinski, Wayne C. Wolsey, Robert Rossi

Publisher:Emil Slowinski, Wayne C. Wolsey, Robert Rossi

Chapter6: Properties Of Hydrates

Section: Chapter Questions

Problem 1ASA: A student is given a sample of a pink manganese (II) chloride hydrate. She weighs the sample in a...

See similar textbooks

Similar questions

1. A gas consist of 70% propane and 30% butane by volume. Find the stoichiometric air-to-fuel ratio. a. 3:14 b. 14: 3 c. 23:1 d. 1:23 2. A furnace is fired with fuel oil with a partial analysis of 7.6% S and 2.8% N. Orsat analysis of the stack gas shows 9.44% CO2, 1.19% CO, 0.4% SO2, 0.47% H2, 6.8% O2 and 81.7% N2. Air supplied is at 23 deg Celsius, 755 mmHg and 85% RH. Calculate the percent excess air. a. 55% b. 78% c. 23% d. 38%
In measurements made in the chimney (stack), the amount of total specific dry stack gas was measured as 11.6 Nm3/kg and the CO2 ratio in the flue gas as 12%. Since 1.47% of the carbon in the fuel is burned as carbon monoxide, what is the carbon (C) ratio in the fuel? a. 75,7% b. 64,6% c. 53,1% d. 60,3%
Aluminum-Lithium alloys have been developed by aircraft industry to reduce the weight and improve the performance of an aircraft. A commercial aircraft skin material having a density of 2.47g/cm? is desired. What is the Li wt% that is required on that material alloy? Density of lithium = 0.534g/cm? Density of aluminum = 2.7g/cm a. 12.28 wt% b. 9.7 wt% c. 4.51 wt% d. 2.3 wt%
Acetylene reacts with HCl in appropriate conditions to form phenolic chloride C₂H3Cl, which is used in plastics industry, according to following reaction C₂H₂ + HCl → C₂H₂Cl If 35 g from acetylene react with 51 g from HCl, calculate: 1. Limiting reactant material. (8 degree) 2. Mass of residual reactant material. (7 degree) {CI= = 35.5 9 mole' H = 1 9 mole & C = 12} mole
10. Gaseous propane at 20 °C is burned with 70% excess air that enters the combustion chamber at a rate of 1.3 kg/min. and at 9°C, 1 atm. Determine a. mass flow rate of fuel b. dew point temperature of product gases 2/2 c. amount of heat transfer per kg of fuel
A chemical manufacturer produces ethylene oxide by burning ethylene gas with air in the presence of catalyst. If the conditions are carefully controlled, a substantial fraction of ethylene remains unconverted and some is completely oxidized to form carbon dioxide and water. Formation of carbon monoxide is negligible. After the gases leaving the absorber is as follows: 9.6%CO2, 3.0%O2 and 6.4% ethylene. Of the ethylene entering the reactor, what percentage is converted to ethylene oxide?
Methane (CH4) is reacted with oxygen (02) over a catalyst to produce acetlyene (C2H2) in the following reaction: 6 CHąlg) + O2lg) –→2 C2H2(g) + 2 CO(g) + 10 H2(g) If a feed containing 150 mol CHg and 50 mol O, is fed into a reactor and the conversion of the limiting reactant is 92 %, determine the concentration of CH, in the product flue gas. Give your answer as a mole percent rounded off to one decimal place.
Please answer this with in 30 mins ! I will upvote !
1. Kindly answer this problem. Thank you.
9:16 Question 14.e of 40 In welding, the temperature of the flame produced by the combustion of acetylene and oxygen varies based on the balance of the two gases in the reaction. The heat is used to melt metal so that pieces of metal can be joined together. 1 4 7 +/- Tap here or pull up for additional resources 2 5 8 . LTE A carburizing flame (excess acetylene) is used to add carbon to a weld. The temperature of a carburizing flame is typically around 935 °C. What is this temperature in °F? Report your answer to three significant figures. | °F Submit 3 6 9 O X x 100
Please for number 3
9. Ethane is burned with air in a continuous steady-state combustion reactor to yield a mixture of carbon monoxide, carbon dioxide, and water. The feed to the reactor contains 10 mol/min C2H6 and 200 mol/min air. The percentage conversion of ethane is 80%, and the gas leaving the reactor contains 8 mol CO2 per mol of CO. Determine the molar flow rate of the ethane gas in the product stream. (2 mol/min)