n industrial load is fed from an AC voltage source (V.) via a transmission-line feeder with an mpedance Zline. The load operates at 30 kW, 0.8 pf lagging and voltage of 240 V-rms angle 0°. he real power and reactive power dissipated in the transmission-line feeder are 1.8 kW and 2.4 EVAR, respectively. ) Draw a schematic diagram of the circuit. 5) Find the impedance of the transmission-line feeder Zine. b) Find the magnitude and the phase angle of the voltage source.

n industrial load is fed from an AC voltage source (V.) via a transmission-line feeder with an mpedance Zline. The load operates at 30 kW, 0.8 pf lagging and voltage of 240 V-rms angle 0°. he real power and reactive power dissipated in the transmission-line feeder are 1.8 kW and 2.4 EVAR, respectively. ) Draw a schematic diagram of the circuit. 5) Find the impedance of the transmission-line feeder Zine. b) Find the magnitude and the phase angle of the voltage source.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. A single-phase are distributor AB is fed from end A and has a total impedance of (0.3-0.3) ohm. At the far end, the voltage V-240V and the current is 100A at a p.f. of 0, 8 lagging. At the mid-point M. a current of 100 A is tapped at a p... of 0.6 lagging with reference to the voltage V_{M} at the midi-point. Calculate the supply voltage V Lambda j sending current I_{N} and the phase angle between V_{A} and V_{E}
If the voltage and current supplied to a circuit orload by a source are˜VS = 170∠(−0.157) V ˜IS = 13∠0.28 Adeterminea. The power supplied by the source which isdissipated as heat or work in the circuit (load).b. The power stored in reactive components in thecircuit (load).c. The power factor angle and power factor.
I need help with this homework question.
In a given system of base power of 250 MW, and bus 3 is taken as reference. The per-unit reactances are X₁2 = 0.2 p.u., X13 = X23 = 0.1 p.u. If the power flow in the system is given as: PF12 = 100 MW, PF13 = 50 MW, PF23 = -150 MW, then the phase angles are Select one: O a. 0₁ = 0.02 rad., 0₂ = 0.06 rad., 03 = 0 rad. O b. None of these O c. 8₁ = 0.02 rad., 02 = -0.06 rad., 03= 0.1 rad. O d. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0.2 rad. O e. 8₁ = 0.02 rad., 8₂ = -0.06 rad., 03 = 0.1 rad. O f. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0 rad.
Describe the concept of three-phase power in electrical systems and its significance in power distribution.
The output of a station with two alternators in parallel is 40MW at 0.75 power factor lagging. One machines is loaded to 20,000KW at 0.8 power factor lagging. Determine the: a. KVA rating and power factor of the load b. KVA rating and power factor of the other alternator
A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of 0.75 lagging. Determine the parallel capacitance required to improve the power factor to: a) 0.9 lagging and b) 0.9 leading. What per cent reduction in line current resulted in part (a)?
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
I need the answer quickly
3. A circuit consists of two impedances. Z1 =20230° and Z2 =25260° 2, in parallel, supplied by a source voltage V=1002600 volts. Determine the power triangle for each of the impedances and for the source.
Two parallel loads are connected to a 120 volt rms, 60 Hz power line. One load absorbs 10 k watts at 0.8 power factor lagging. The second load absorbs 4 k watts at 0.9 power factor leading. Determine the real (watts) and reactive (VARS) power of the combined load.
Relation between power and power factor in ac circuits . Discuss the power triangle for a load an ac circuit .