Н) B 30° 250 mm 250 mm 300 mm 50 mm 50 mm 400 N

Q: A 200mm lever and 240mm pulley are welded to the BE shaft which in turn is supported by bearings at…

A:

Q: A lever AB is hinged at C and attached to a control cable at A . If the lever is subjected to a…

A: Draw the FBD for a better understanding of the given problem.

Q: Knowing that each pulley has a radius of 250 mm, determine the components of the reactions at D and…

A: Given data as per the question the radius of each pulley = 250 mm Force  = 4.8KN considering free…

Q: The frame shown is supported by three cables and a ball-and-socket joint at A. For P = 0, determine…

A: To find: Tension in each cable The reaction at point A.   Free body diagram of the frame:

Q: Two transmission belts pass over sheaves welded to an axle supported by bearings at B and D. The…

A:

Q: Frame ABCD is supported by a ball-and-socket joint at A and by three cables. For a = 150 mm,…

A: Draw the free-body diagram of the system.

Q: 4.174 The weight W = 6 kN hangs from the cable which passes over the pulley at F. Neglecting the…

A: Consider the algebraic sum of moments about point A .∑MA=0Calculate the algebraic sum of moments…

Q: The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at…

A:

Q: 3.19. The vertical bar A is built into the ground at B. The block W which weighs 300 lb is supported…

A:

Q: Determine the components of the reactions at D and E if the frame is loaded by a clockwise couple of…

A: (a) Consider the first case where a 150 N.m CW moment acts on the point A. Consider the free body…

Q: 1. For the frame shown, determine the reaction at E assuming a pinned support. The tension in the…

A:

Q: The spanner shown is used to rotate a shaft. A pin fits in a hole at A, while a flat, frictionless…

A:

Q: The lid of a roof scuttle weighs 75 lb. It is hinged at corners A and B and maintained in the…

A: To determine: Magnitude of the force exerted by the rod CD                         The reaction at…

Q: 1.8 m 1.8 m B 2.1 m C 1.8 m. 1.2 m 4 kN

A:

Q: 4.88 Rod AB is bent into the shape of an are of circle and is lodged between two pegs D and E. It…

A:

Q: The lid of a roof scuttle weighs 75 lb. It is hinged at corners A and B and maintained in the…

A: Given data: The coordinates of the A and B are A =(0, 0, 0) B = (26, 0, 0) The scuttle weighs, W =…

Q: 1. Determine the vertical and horizontal components of the reactions at pin A and the tension…

A: Solution:

Q: The uniform (18kg) bar OA is held in the position Shown by the pin at o and the Cable AB. Determine…

A: Given-Data:- Weight of the bar OA (W)=18 kg= 18 ×9.81=176.58kgm/s2 To-Find:- Tension(T) Reaction at…

Q: 40 mm 80 mm 120 mm 200 mm T E 120'mm 720 N B

A: The tension in the cord is  Σ M = 0  860(200) - T(120) = 0  T(120) = 172000  T =1433.33N The tension…

Q: Knowing that the pulley has a radius of 75 mm, determine the components of the reactions at A and B.

A: Given data as per the question The radius of pulley =75 mm Force acting on the string of the pulley…

Q: A uniform circular rod with a weight of 8 lb and radius of 10 in. is attached to a pin at C and to…

A: Given   The weight of the circular rod, W = 8 lb.   Radius, r = 10 in.

Q: For the frame shown, determine the magnitude of the pin reaction at B. Neglect the weight of the…

A: Solution  FBD

Q: A force P is applied to a bent rod ABC. Determine the reactions at the supports

A:

Q: Knowing that the pulley has a radius of 50 mm, determine the components of the reactions at B and E.

A: Free Body Diagram 1) Entire Assembly 2) Member ACE

Q: The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at…

A: