Answered: N 1200N 400 mm 150 5 mm tipico 20 mm 25…

Engineering

Civil Engineering

N 1200N 400 mm 150 5 mm tipico 20 mm 25 mm 20 mm (b) 45 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABC is supported by bronze rod and aluminum rod as shown in the figure. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod has an elastic modulus of 15,000ksi and a diameter of 0.65in. Aluminum rod (2) has an elastic modulus of 10,000ksi and a diameter of 0.85in. Aluminum rod (3) has a diameter of 1.20in. The yield strength of the bronze is 52ksi, and the yield strength of the aluminum is 42ksi.a. Determine the magnitude of load P that can safely be applied to the structure if a minimum factor of safety of 1.70 is required.b. Determine the deflection of point D for the load determined in question (a).c. The pin used at B has an ultimate shear strength of 56ksi. If a factor of safety of 3.0 is required for this double shear pin connection, determine the minimum pin diameter that can be used at B.
The beam is made from three polystyrene strips that are glued together as shown. If the glue has a shear strength of 80 kPa, determine the maximum load P that can be applied without causing the glue to lose its bond. 30 mm 40 mm 60 mm 40 mm 30 mm -20 mm A P +im+im+i 1m- 1m 1 m-0.8 m-
Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa], located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. K4N/M 2m B 10kN/mm 4m 2m D Steel Aluminum 42mm 20 mm 13 mm
A structural component in a fighter jet aircraft has a cellular cross-section (Fig. Q1). The component is 2 m long and is fabricated from an Al alloy, whose modulus of rigidity is 30 GPa. During a certain maneuver of the aircraft, a torque of 40 Nm is applied to the component. Using the Membrane Analogy Method, calculate: (a) the torsional shear stress in each cell of the cross-section; and (b) the angle of twist of the component, giving your answer in degrees. 2mm 75 15m 600mm FIG. Q1
i need the answer quickly
Under normal conditions the average shear modulus of Au is 27 GPa while that of Cu is 46 GPa. What does this infer?
Mechanies of Materials II: 2019-2020 University of Misan College of Engineering/Department of Civil Engineering Dr. Mustafa Chasib Jasim HWI For the beam shown in the figure below: i- Calculate the support reactions at B and D. ii- Calculate the distribution of shear V in the beam and illustrate with a diagram that shows magnitudes. i-Calculate the distribution of moment M in the beam and illustrate with a diagram that shows magnitudes, 700 1,500 Ib 200 Ibit
Given the 180 mm x 360 mm rectangular beam as shown in the figure. 100 kN/m 20 kN-m 50 kN/m 360 mm 1.5 m 5 m 180 mm What is the bending or flexural stress in a fiber 20mm from the top of the beam at the left support in MPa?
The nut on a bolt is tightened by applying a force of P = 38 lb to the end of a wrench at a distance of a = 6.0 in. from the axis of the bolt. The body of the bolt has an outside diameter of d = 0.425 in. What is the maximum torsional shear stress in the body of the bolt?
Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa], located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. K4N/M 2m B 10kN/mm 4m 2m D Steel Aluminum 42mm 20 mm 13 mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10 3 mm while those at CD decrease 90 x 10 3 mm in the 280-mm-gage length. Using E = 160 GPa, %D determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 60 mm, b = 140 mm, and %3D C = 80 mm. gage length a mm b mml c mm
Problem 3 For the compound beam shown in Figure 4, determine the reaction forces, calculate the stress in each member, and determine the deformation in each beam using the Direct Stiffness Method. 3 ft 2 ft 2 ft y 500 lb 300 ft-lb 1= 0.948 in ¹ E = 30 106 psi I = 0.198 in ¹ E = 30-106 psi