Motion of the sliding block Pin the rotating radial slot is controlled by the power screw as shown. For the instant represented, 0 = 0.15 rad/s. ö = -0.05 rad/s, and r= 350 mm. Also, the screw turns at a constant speed giving i= 35 mm/s. For this instant, determine the magnitudes of the velocity v and acceleration a of P. Part 1 Correct Find the r- and ecomponents of velocity. Answer: V, = 35 mm/s 52.5 mm/s eTextbook and Media Hint Attempts: 1 of 15 used Part 2 Determine the magnitude v of the velocity of P. Answer: v= mm/s

Motion of the sliding block Pin the rotating radial slot is controlled by the power screw as shown. For the instant represented, 0 = 0.15 rad/s. ö = -0.05 rad/s, and r= 350 mm. Also, the screw turns at a constant speed giving i= 35 mm/s. For this instant, determine the magnitudes of the velocity v and acceleration a of P. Part 1 Correct Find the r- and ecomponents of velocity. Answer: V, = 35 mm/s 52.5 mm/s eTextbook and Media Hint Attempts: 1 of 15 used Part 2 Determine the magnitude v of the velocity of P. Answer: v= mm/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1. Member AB is rotating (about fixed point A) with angular velocity (@ = 1 rad/sec) and angular acceleration (a = 2 rad/sec?) and driving the link CD (rotating about fixed point D at constant velocity) as shown in figure. Select five right answers. (a) Tangential Acceleration (a:) of link AB will not be zero (b) Tangential Acceleration (a) of link AB will be zero D 450mm (c) Tangential Acceleration (a,) of link CD will not be zero 200 mm 100 mm 60 H (d) Tangential Acceleration (a,) of link CD will be zero (e) All points on link CB will have same linear velocity 0 All points on link CB will have same angular velocity Formula • Tangential acceleration of a rotating link -ra • Radial (normal) acceleration of a rotating link = v³ /r= wr velocity of a rotating Ink (v) = r.w (g) Angular acceleration (a) for link CD will be zero (h) Angular acceleration (a) for link CB will not be zero Q2. Magnitude of linear velocity of any point “H" located at the half of the length of a rotating link CB…
Dont copy from others also I have mentioned the answers which is correct so u can match only part a I'm getting wrong but do all correct
2. The gear A on the drive shaft of an outboard motor has a radius of ½ inch while the meshed pinion gear on B has a radius of 1% inches. If the drive starts from rest and is accelerated at a constant a = 200 rad/s², what is the speed, tangential acceleration, and normal acceleration at point P on the propeller after 3 seconds. 2.20 in
Member AB has the angular velocity WAB = 4.5 rad/s and angular acceleration a AB = 6 rad/s². (Figure 1) Figure A 200 mm 300 mm 1 @AB a AB B 500 mm 0= 60° 1 of 1 Determine the angular acceleration of member CD at the instant shown measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular acceleration is counterclockwise and negative value if the angular acceleration is clockwise. ACD = Submit VO ΑΣΦ ↓↑ vec 325 Previous Answers Request Answer X Incorrect; Try Again < Return to Assignment Review Provide Feedback ? rad/s²
For the Mechanism shown, find the acceleration of the slider link4 using Vector loop method. Assume r3=1 cm. Y B KE 13 =90°. 00₂= 10 rad/s CCW (constant) X Hand written plz a
box answer
The angel between OS and the horizontal is 160 degrees. please draw the velocity diagram and the acceleration diagram (hand written)
Problem 1 A Mechanisms Enthusiast Club is using a rigid bar (length LAB = 18 in.) with wheels riding along horizontal and sloped (angle = 45°) surfaces to demonstrate rigid body acceleration. Point B is measured with video analysis software at the instant shown (ß = 30°) to be traveling at VB = 20 in/s to the right while slowing down at ag = 5 in/s². A Using vector math, determine the velocity and acceleration of point A. Ө B G LAB ав B VB
Bar OC rotates with a clockwise angular velocity woc = 5.3 rad/s and a counterclockwise angular acceleration doc = 4.6 rad/s². The bar OC is a slotted member which accommodates the pin A attached to the sector. Determine the angular velocity w and the angular acceleration a of the sector. The angular velocity and the angular acceleration are positive if counterclockwise, negative if clockwise. Assume OA = 500 mm, d = 385 mm, 0 = 21°. Answers: W = B a = i i d aoc rad/s rad/s² @oc
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration a (both counterclockwise). 2) if W = 4.2 rad/s and a = 8.0 rad/s2, what is the magnitude of the linear velocity of point A? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. 0.5 m A 0, a B Your Answer: Answer units
Note: Read the question carefully and give me right solution clear calculations . Careful with angular velocity direction
Find the angular velocity and angular acceleration of the wheel according to the values given in the motion of the system seen at this position.