Moment Shear The beam shown is pinned at A and roller at C and is loaded with a point load, F = 43 lb, a moment, M = 277lb (CW), and has a distributed load, w=13lb/ft and has dimensions, a = 35 ft, b = 20 ft, and c=11ft. The support reactions are as follows: Ay 46 lb, Cy 201lb↑ a. What is the shear equation for AB? C b. What is the moment equation for section AB? c. What is the shear equation for CD? d. What is the moment equation for section CD? e. What is the shear equation for BC? f. What is the moment equation for section BC? g. What is the moment equation for section AB? h. Draw the full shear diagram for part I. Include max/min values. d. Draw the full moment diagram for part I. Include max/min values F W M

Q: ng based on the degress scal from 0 to 72

A: 4 steps are present in the IC cycle. inlet compression power exhaust

Q: Which of the following statements is not true? Select one: O a. Reports can contain bulleted or…

A: As we know Equations should be written in a symmetric manner, not just in the left margin. Equation…

Q: Make the part program using CNC code.        Tool Dia. = 6 mm        depth of cut 3.0 mm…

A: Tool Dia. = D =6 mm depth of cut = d= 3 mm (Use G90 code)  To find: Make the part program using CNC…

Q: Worksheet 6-3 00 1. Type of view 2. Type of view 3. Type of view 4. Type of view 5. Is view 4 easier…

A: Solution: Given Data:

Q: Vrite a complete program to mill around the part. The endmill is .500 diameter, and yo nt to leave…

A:

Q: bäi The command using to insert :seal is

A: The Incident Command System is a standardized approach to the command, control, and coordination…

Q: What is a microcontroller? 1. General purpose device that can be programmed to carry out a finite…

A: Given question is related to electromechanical devices and controllers.

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

A:

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Draw the isometric view.

Q: The correct choice is what

A:

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: I need answers to this part, thank you.

A: The correct matches are:

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: where are the graphs?

A: Given data in the related question: Maximum speed = vf = 183.58 mi/hr Distance travelled = 5 mi Time…

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Draft and annotate the below sketch using AutoCAD Note: colour the hatching lines with different…

A:

Q: Given the Top View, Right View, and the outline of the Front View. Create a section view based on…

A:

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: To make the 3d sketch for each of the frames which contain the views in the plan

A:

Q: The shortest distance between a line and a point is achieved when? a) A line is drawn at 90 degrees…

A: Given  The shortest distance between a line and a point is achieved when? a) A line is drawn at 90…

Q: Create a list of operations for the blueprint provided below. The list of operations must be in…

A: The chronological order of operation of the given part is mentioned below  for this part the list of…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: what is the cause of an extremely hard brake pedal

A: To the left of the accelerator, the brake pedal is positioned on the floor. It applies the brakes…

Q: General Questions Not Directly Print Related) 1.  ____________use conventional symbols with single…

A: Fill in the blanks

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

A:

Q: By using AutoCAD command draw the following samples with possible fitting. 1- Main door 2- Boiler 3-…

A: Given question: By using AutoCAD commands draw the following : 1. Main Door 2. Boiler 3.…

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: From the following identify the true statement. O In electrical safety precaution, all non-metallic…

A: out of the 4 statements

Q: Using autocad draw necessary views. Kindly all the views I'll rate your solution

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 7-Either the following text: Standardization is an activity that consists of developing rules…

A: It is asked to generate stick scriptWhat is te role of orientation marker How the inscription…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: a. You are a mechanical engineer tasked with overseeing the equipment used in constructing a…

A: Given datadistance of the construction load from tower (r) = 62.42e0.02j m F = 5000e-1.57j Nl =…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…