Moist air at 21 Cº DBT and 15 C° WBT and standard atmospheric pressure is humidified by water spray. If for each one kg of dry air passing through the duct 0.002 kg of water at 100 C° is injected and totally evaporated. Draw the psychometric and schematic figures of process and calculate for the air leaving the spray chamber: a- The moisture content. b- The enthalpy c- Dry bulb temperature.

Moist air at 21 Cº DBT and 15 C° WBT and standard atmospheric pressure is humidified by water spray. If for each one kg of dry air passing through the duct 0.002 kg of water at 100 C° is injected and totally evaporated. Draw the psychometric and schematic figures of process and calculate for the air leaving the spray chamber: a- The moisture content. b- The enthalpy c- Dry bulb temperature.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

There are 300 cubic meter/min of atmospheric air initially at 25 C wet bulb temperature and 60 % RH flowing thru air duct header junction mixed with 400 cubic meter/min of cold air at 18 C dry bulb temperature and 10 C wet bulb temperature. After the adiabatic mixing, determine for the mixture:a) relative humidity b) specific humidityc) dewpoint temperatured) plot the process on the psychrometric chart and label completely
A dryer is to deliver 1000 kg/hour of palay with a final moisture content of 10%. The initial moisture content in the feed is 15% at atmospheric condition with 32°C dry bulb and 21°C wet bulb. The dryer operates adiabatically while the relative humidity of the hot humid air from the dryer is 80%. If the steam pressure supplied to the heater is 2 MPaa, determine the following, show solution in an orderly manner and select the best answer: 1) amount of palay supplied to the dryer in kg/hour а. 14,192 b. 13,980 c. 13,332 d. 13,679 2) amount of air supplied to the dryer in kg/hour а. 1039 b. 1059 c. 1079 d. 1000 3) temperature of the hot humid air from the dryer а. 29.3 b. 26.3 с. 20.3 d. 23.3
An air handler supplies 2.36 m3 /sec at a temperature of 12°C. The air handler was designed for 0.5 m3 /sec of outside air at 32oC DB and 26°C WB. The remaining return air from the space is at 25°C DB and 55% relative humidity. What are the entering conditions of the air into the coil, in DB and WB? Air pressure is 101.325 kPa
Air at 90○F and 20% relative humidity is cooled to 75○F. Assuming standard atmospheric pressure when the inlet flow rate is 1500 ft3/min, what amount of thermodynamic conditions are needed to achieve the resulting temperature?
Required information Problem 14.108 - Cooling Tower Assessment NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The cooling water from the condenser of a power plant enters a wet cooling tower at 40°C at a rate of 91 kg/s. The water is cooled to 25°C in the cooling tower by air that enters the tower at 1 atm, 23°C, and 60 percent relative humidity and leaves saturated at 32°C. Neglect the power input to the fan. Use data from the psychrometric chart and tables. Problem 14.108.a - Cooling Tower Assessment Determine the volume flow rate of air into the cooling tower. m³/s. The volume flow rate of air is
Air enters a humidifier at 34.25°C and 30% RH. If the air leaves the humidifier at 70% RH. Determine: The exit dry-bulb temperature of the air in °C.The saturation effectiveness in %.
Can you make a schematic diagram for this problem? 600 lps of air at 30°C dry-bulb and 22°C wet-bulb temperatures is heated to a temperature of 45°C and enters the dryer. The air leaves the dryer adiabatically and its relative humidity is 70%. Determine: (a.) The water evaporated kg/hr; (b.) The volume air leaving the dryer in cu.m/min; and (c.) kJ requirement of the dryer per kg of water evaporated.
H2
6kg/s of return air at 20 °C and 40% relative humidity are mixed with 2 kg/s of outside air at 40 °C and 60% relative humidity before entering a cooling coil. The mixed air is then cooled sensibly to 14 °C. SHR30.6. The mixing enthalpy hm in kJ/kg is