Model the Earth as a sphere of radius R. If two antennas are both at height h above the ground, at what distance r does the ground block the "line of sight" between them? If R = 6,371 km and h = 10 m, what is r? If R = 6, 371 km and r = 100 km, what is h? Solve for both values to the nearest meter. h Earth R h

Q: answer ASAP

A:

Q: Capacitors are used after the converter toA. smooth out the DC current.B. suppress the noise.C.…

A: A converter is used to convert the input AC voltage into DC voltage. The capacitor is used after the…

Q: Shunt generators are most suited for stable parallel oneration because of linear voltage…

A: The best kind of DC generator for reliable parallel operation is a shunt generator because of its…

Q: An inductive load of 100 Ohm and 200mH connected in series to thyristor supplied by 200V dc source.…

A: In this question we will find that SCR will be fired or not by given data...

Q: In DC generators, lap winding is suitable for ) high voltage, high current low voltage, high current…

A:

Q: 1) Construct the Magnitude and Phase Plot for the following transfer functions, 40(s + 2) H(s) = (s…

A: Given The given transfer function can  be simplified as

Q: A liquid level control is shown in Figure Q4(c). Pump will run when the liquid is below the low…

A: To design ladder diagram

Q: 91 The disadvantage associated with an electrodynamic instrument is that it consumes more power it…

A:

Q: B- compare ( in 5 point only) between a dArsonval move Electrodynamometer. a dArsonval movement…

A: In this question we need to write the difference between darsonval movement and electrodynamometer .

Q: What is the accurate LVDT output voltage when the core is at the centre position? a. 5.22V b. 2.5V…

A: Given: LVDT

Q: Get the block diagram and transfer function of the following diagram

A: The given circuit of a DC generator is shown below. It is asked to find the transfer function and…

Q: /Design Dc Dc converterto produced -15 V output Prom Source Varid from 12 to 18 V. The loud…

A:

Q: What is the purpose of Kirchoff loops?

A:

Q: Examples of Close loop versu open loop

A: We need to explain the examples of open loop and closed loop control systems. A system just contains…

Q: The offset voltage describes the dc component of a dc electrical .signal

A: according to the question we want to know what offset voltage describes

Q: Draw an illustration of an open grinding circuit. Draw an illustration of a closed grinding circuit.

A: Open grinding circuit consisit of one or more than one friding mills which are either connected in…

Q: OSC1 +Ch1_ +Ch2. 1k Vo 4Vp-p/1kHz 1n4001

A:

Q: 1- For Buck type DC-DC converter, the occupancy-void ratio is 0.5, the input voltage is 12V, the…

A: Given: Buck Converter  Vin=12 V  Duty Ratio= 0.5 current of coil= 2A

Q: Find out the power of the following signal: x(n)=2ej3n Please show all the steps

A: For any discrete-time signal x(n), the power of the signal can be computed using the following…

Q: What is the maximum frequency of operation for the following configuration? DTsul dlyl DTsu2Q dly2…

A: Flip flop is a latch with additional control input (clock or enable ). A flip flop is used to store…

Q: the BLDC motors have the advantage of Low Maintenance Compactness High Efficiency O All of the…

A:

Q: In forward regeneration mode of operation in chopper, one of the following condition happens Load…

A: Forward regeneration mode of the operation in chopper , what would be happened in the region

Q: Choose the correct waveform for the given Negative Edge triggered D- flipflop among the following:…

A: The waveform for negative edge-triggered D flip-flop is the first reason is stated below: - At…

Q: A commutator has 456 segments. Indicate whether or not the windings are possible a. Duplex-wave,…

A:

Q: www ww R₂ C₁ R₁ C₂ 2₁ Rf R3 + R₁ D₁ C3 Vout

A: The above circuit is the circuit of the Wein bridge for the automatic gain control. The Zener diode…

Q: AVcc RA = 1kr NES55 Vout Oulput 3 2. 9. .C2 =0.0 luf figue 1. Refer to the fiqure 1: @ Calculate the…

A:

Q: a. HIGH to LOW edge O b. falling edge O c. trailing edge leedin g od

A: In this question, positive going pulse is given..And asking about rising edge..

Q: select the right answer: The remainder in cyclic redundancy checking represents the a. The CRC b.…

A: the error

Q: Consider a 6 DoF manipulator with variables q1, q2, q3, q4, q5, qnd q6. The position is usually…

A: Generally q1, q2 , q3 gives the position in a 6 DoF manipulator .

Q: 4. Load regulation is determined by a. changes in load current and the input voltage b changes in…

A: To do: 4. we have to select right option with respect to Load regulation. 5. we have to select right…

Q: I want a report on Characteristic of Self- Excited Shunt

A: In a self-excited generator, the current to the field winding is provided by the generator. and in…

Q: Due to an armature reaction in DC mach the generated volt is O Decrease O Increase or decrease O…

A: In this we will write about generated voltage in dc machine due to armature reaction...

Q: What's the peak time for this system with its closed-loop poles as shown? j4 12 16 -4 -2 -12 %23 -j6…

A:

Q: Prove that the fluctuation of voltage at the load end is largely a function of the reactive power,…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Routh Hurwitzof closed loop system with variable gain.

A:

Q: What is a prime mover? What are different types of it?

A:

Antenna Characteristics

The antenna is an important concept in the domain of electronics and communication engineering. An antenna forms an integral part of many commonly used devices such as wireless modems, routers, game controllers, mobile phones, bluetooth devices, and so on. In simple terms, any wireless communication makes use of antennas to serve the purpose. An antenna, also known by the term 'arial', is an electrical device that converts electrical signals into electromagnetic waves or electromagnetic waves into electrical signals. An antenna contains a transmission line usually made up of co-axial cable, it then receives the signals and converts them into electromagnetic waves, which are then transmitted via space into their required destination. A communication system essentially makes use of two antennas, a transmission antenna, which converts electrical signals into electromagnetic waves, and a receiving antenna, which receives the electromagnetic waves and converts them back into electrical signals.