model of an airplane has a scale 1:20. If the model and the airplane is made up of the same haterial, what is the weight of the airplane if the model weighs 420 g?

Q: Determine the force in each member of the loaded truss. All triangles are isosceles. 10 kN 4 m E 4 m…

A:

Q: Example 168 For the frame shown below, the initial displaceme velocity is 13 mm/s. Damping is 10% of…

A:

Q: compression. Use combination of Method of Joints and Method of Sections. Note Determine the force in…

A: It is given that : To Find - We need to find forces in each members using both method of section…

Q: A mechanic uses a piece of pipe AB as a lever when tightening an alternator belt. When he pushes…

A:

Q: Determine the vertical deflection at point A of the steel beam. Use E = 200 GPa and I = 100x10^6…

A:

Q: 1. Determine the moment about point A for the force system shown if each square represents 1m. 39 N…

A: A loaded square plan has been given and it has been asked to determine moment at A. Please refer…

Q: Q.27 A reservoir discharges through a sluice 0.915 m wide by 1.22 m deep. The top of the opening is…

A:

Q: 4. The 500-kg uniform beam is subjected to the three external loads as shown. Compute the reactions…

A:

Q: A small tube with a cross-sectional area of 30 cm? is filled with soil and laid horizontally. The…

A:

Q: Two plates each with thickness t = bolted together with 6-22 mm a bolts forming a lap connection.…

A: Permissible stress is referred to the allowable stress or allowable strength. The bearing capacity…

Q: For a given wing-body combination, the aerodynamic center lies 0.03 chord length ahead of the center…

A:

Q: Solve for the reactions using portal method. 70 kN 70 kN- A E 35 kN 9m B M K G C -6m- 9m L H D T 4.8…

A:

Q: surveying technique shall be used in cadastral surveying'

A: To explain the surveying techniques used in cadastral surveying and explain the reason

Q: Q- In the layout of an MG track, the versine of a horizontal circular curve is measured over a 17 m…

A: Degree of curve = 2 Chord length = 17 m  To calculate: versine of curve.

Q: A loaded beam, 60 mm wide by 200 mm high and 8 m long, has the shear and moment diagrams as shown…

A: Since BMD and SFD are given so we do not need to draw. We know that ; MI = σy  where ; M = Bending…

Q: It takes an apprentice twice as long as it takes an experienced carpenter to do a piece of work.…

A:

Q: QUESTION 14 A non-potable water storage tank is at an elevation of 37 feet above the discharge for…

A:

Q: Problem 1a. Determine whether each of the beams and frames below are internally determinate,…

A: No. of reaction = (3 for fixed 2 for hinge 1 for roller)  a.)No. of Reaction = 4 (2+1+1) (2 for…

Q: PROBLEM 6: A float to be used as a level indicator is being designed to float in oil, which has a…

A:

Q: Problem 29: A light foam cup similar to a disposable coffee cup has a weight of 0.05 N. A steel bar…

A:

Q: A kite at a height of 60 ft, is moving horizontally at a rate of 4ft per second away from a boy who…

A:

Q: The 200-kg crate in Figure (a) is suspended using ropes AB and AC. Each rope can withstand a maximum…

A:

Q: Q.14.12 A field pumping test was conducted from an aquifer of sandy soil of 4 m thickness confined…

A:

Q: 1.5P KN P kN- A a. -21.3 kN b. -21.9 kN c. -20.6 kN d. 17.5 kN 1.5 m GH 3 m Force at member GH -3 m…

A:

Q: 22. A mass weighing 4 pounds stretches a spring 4 inches. (a) Formulate an initial-value problem…

A:

Q: A triangle has vertices at A( - 3, - 1 ), B( 6, 3 ), and C( 4, - 2). Find the equation of the…

A:

Q: 1. Pis a cube with 300mm sides and weighs 45kg per cubic meter. Rope CB is 20mm in diameter and can…

A:

Q: TOPIC: MOMENT OF A FORCE A foot valve for a pneumatic system is hinged at B. Knowing that a = 28°,…

A:

Q: The maximum tension occurring in a suspended cable is 5 kN and horizontal tension is 4 kN. The…

A: Tmax = 5kN H = 4 kN

Q: 5. A 5-m-high, 5-m-wide rectangular plate blocks the end of a 4-m-deep freshwater channel, as shown…

A:

Q: PROBLEM 5: Will the cylinder float described in Problem 4 be stable if placed in the fluid with its…

A:

Q: 3.28-C CE Board May 2012 A lapped, bolted tension member is shown. Diameter of bolts are 18 mm Ø and…

A: The diameter of the bolts = 18 mm  The thickness of the plate = 11 mm The yield strength of the…

Q: PROBLEM 23: Will the cylinder shown in Figure 11 and described in Problem 22 be stable in the shown…

A:

Q: 7. The beam has the following data: fy = 275 MPa, fc' = 30 MPa, base = 360 mm, effective depth = 450…

A:

Q: Statically undetermined system and its bending moment diagram for elastic case are given in the…

A:

Q: Example 4.7 A field pumping test was conducted from an aquifer of sandy soil of 4 m thickness…

A: Above given data we have to find permeability k

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.