mift pulse Reset 7/A three bit shift register is shown below to have 000 again, the number of clock pulses required would be: D D Q D Q Q CP CP A. 2 B. 3 C 6 D. 7 Q' o' CP a'

Q: is the most important segment and it contains the actual assembly language instructions to be…

A: microprocessor works based on the assembly lenguage instruction provided to it.

Q: The number of clock pulses required to load the value (1011) into a 4- bit parallel load shift left…

A: Registers are made up of flip flops , are used to store string of bits into sequential order. There…

Q: Q2. (i) A switch tail ring counter (Johnson counter) uses the complement of the serial output of a…

A:

Q: Q2.) Determine the count sequence for feed-back shift register shown below assume the initial state…

A:

Q: B A OUT AR of-4 0 tiplexer TPL Tristate CLK P Flip-flop output buffer S, =0 So =o clock SP OE LA 320

A:

Q: What is the number of select inputs in a multiplexer with 4 input lines? O a. 4 O b. 1 O c. None O…

A: Multiplexer with 2n inputs has n selection lines and we have only single output.

Q: If the input is 1, the output is tied to the signal at input 1. Otherwise the output is connected to…

A: According to the question, we need to draw the output waveform for the circuit given below

Q: clr id Register function Clear 1 Maintain the present value 1 Complement of the present value 1 1…

A: We use n flip flop and  n  4*1 multiplexer for building register with clr and I'd as selection line…

Q: DRAW THE OUTPUT OF THE TIMING DIGRAM BELOW. LET INITIAL Q=I AND THE CLOCK IS NEGATIVE EDOE…

A:

Q: 1-1-0-0 information is applied sequentially to the 4-bit shift register circuit, which consists of D…

A:

Q: can you explain in detail what is random errors and how to limit it

A: A coincidental discrepancy between the observed and true values of anything is known as a random…

Q: Create the complete count sequence table and draw the timing diagram:

A: To Create the complete count sequence table and draw the timing diagram:

Q: Q1\ If you have a data (1010110111) for (shift right register &shift left register ) what is the…

A: Since there is 10 bit.

Q: The number of clock pulses required to load the value (1001) into a 4- bit serial in shift right…

A: The explanation is as follows.

Q: There are three (3) sets of four bits sequence waiting to be loaded into the shift register.…

A: The given figure shows 4 bit parallel input and serial output shift register

Q: Can you determine the difference between the various shift register types?

A: Resistor A resistor is a passive two-terminal electrical component used in circuits to implement…

Q: Table 3. FF content of a 3-bit ripple counter. Clock Cycle A 1 3 4

A:

Q: For the three code words:C1= [110110011], C2= [100101100]andC3=[111100101]. Determine the possible…

A:

Q: * Q: STATUS Register has individual bits indicate status of ALU operations 6 are status flags and 3…

A: In this question , we will write about status flag and control flag in 8086 microprocessor....

Q: Dados Q S T CLK CLK rO CLK CLK K K R K K Pulsos de deslocamento Pulsos de deslocamento T1 T2 T3 T4…

A: Shift register

Q: QUESTION 44 The 8259 is a O Low priority interrupt O Tristate buffer Programmable Peripheral…

A: Intel 8259 is a very important device and very commonly with 8085/8086 systems.

Q: If the initial state for LFSR shown below [Q3 Q2 Q1 Q0] = [1010], what is the state after five clock…

A:

Q: Motors take electrical energy and produce O a Radiant energy Ob Thermal energy OC Mechanical energy…

A: We need to select correct option for given statement .

Q: The initial contents of the 4-bit serial-in-parallel-out shift register shown in the figure below is…

A:

Q: Add and mutiply the following numbers without c Converting them to decimal show work Binary number…

A: Given:i) Binary number: 1011 and 11ii) Binary number: 1101 and 10iii) Hexadecimal numbers 45H and…

Q: B. Determine the amount of time delay operation of 12-bit serial in / serial out shift register Data…

A: For 12bit SISO register  We require 12 flip flops and each flip flop has a time delay Tpd. Therefore…

Q: 12 With a counter 10 lights willI be controlled. At the first clock pulse all lights will be ON (1).…

A: Given data: A counter 10 light  will be controller. The counter is mode 10 counter.

Q: I. CONVERT THE FOLLOWING NUMBER SYSTEM. OCTAL BINARY 10101100.001 715.32 DECIMAL HEXADECIMAL

A:

Q: Write a program using interrupts to simultaneously create 6KHZ and 300 HZ

A: first square wave :6 kHz  second square wave : 300 Hz  Assumption: assumed 8051 micro controller…

Q: Can you determine the difference between the various shift register types?

A: Shift register: When a set of flip flop is connected in series, the combination is known as…

Q: (d) In a certain clock generation circuitry, the input range of the PLL is 3MHZ – 6MHZ. If the input…

A: A phase-locked loop (also known as a phase lock loop or PLL) is a signal processing device that…

Q: What is the decimal form of the binary number 101.11? O 5.75 O 6.25 O 5.375 O 6.125

A: