© Cengage Learning UNIT 12 Fillet Welds 161 7. Why is this particular section shown? 11. How many drilled holes will these parts contain before welding is performed? 8. a. How is the 3" pipe fastened to the cylindrical plate? 12. What hole size is required for the " std. pipe? (Refer to Appendix 4.) b. How is the " pipe fastened to the 3" pipe? %3D 13. What hole size(s) are missing on the drawing? 9. What is the significance of "six holes ES"? 14. On the pictorial drawing below, show the welds called for on the drawing and identify each weld. 10. In what order should this bracket be assembled and welded? Give reason(s) for the order selected. 1/8 2015 Cengage Learning Refer to the drawing Bracket below. 1. Explain fully the meaning of each of the welding symbols used on the drawing. 2. How far apart (in degrees) are the equally spaced drilled holes? 3. Define the dimension 3" XS BI Pipe. 4. How many parts does this bracket consist of? 5. What plate size is used? 6. What type of section is represented by section A-A? 0.250 DRILLTHRU SIX HOLES EQUALLY SPACED 23° CYLINDRICAL PLATE 1" STD 8 PIPE E. A 3" XS BI PIPE 01013" 3" 8. $12! B 3. 32 25" 337 5" 2" HH !..6 D. BRACKET

© Cengage Learning UNIT 12 Fillet Welds 161 7. Why is this particular section shown? 11. How many drilled holes will these parts contain before welding is performed? 8. a. How is the 3" pipe fastened to the cylindrical plate? 12. What hole size is required for the " std. pipe? (Refer to Appendix 4.) b. How is the " pipe fastened to the 3" pipe? %3D 13. What hole size(s) are missing on the drawing? 9. What is the significance of "six holes ES"? 14. On the pictorial drawing below, show the welds called for on the drawing and identify each weld. 10. In what order should this bracket be assembled and welded? Give reason(s) for the order selected. 1/8 2015 Cengage Learning Refer to the drawing Bracket below. 1. Explain fully the meaning of each of the welding symbols used on the drawing. 2. How far apart (in degrees) are the equally spaced drilled holes? 3. Define the dimension 3" XS BI Pipe. 4. How many parts does this bracket consist of? 5. What plate size is used? 6. What type of section is represented by section A-A? 0.250 DRILLTHRU SIX HOLES EQUALLY SPACED 23° CYLINDRICAL PLATE 1" STD 8 PIPE E. A 3" XS BI PIPE 01013" 3" 8. $12! B 3. 32 25" 337 5" 2" HH !..6 D. BRACKET

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

11)lf length of a fillet weld is and leg length is h, then area of throat can be given by: O 0.707 hl O1.414hl Ohl O None
17. Which part of the marking gauge is used to mark lines on wood? a. To measure the ductility of weld metal b. To test the skill of a welder To perform a non-destructive test d. To approve welds to certain standards C. ar an internal force in a mato
E. If the welding process is to be changed from MMAW to MIG/MAG, do you need to re-qualify the welding procedure? Why?
10 Mark the correct statement about Gas Metal Arc Welding. a) Argon gas is used in MAG Welding b) TIG Welding uses a copper electrode MAG is used in the welding of plain carbon and low alloy steels CO2 gas is used in TIG Welding
Seam-welding is .6 Multi-spot welding process Continuous spot welding process Used to form mesh Used for welding cylindrical objects O QO O
7) On increasing the diameter of the SAW electrode, keeping the same current and arc length Width of the weld zone increases and Weld penetration decreases Both width of the weld zone and Weld penetration increases Width of the weld zone decreases and Weld penetration increases Both width of the weld zone and Weld penetration decreases
Joining the sheets at specific locations under the heat and pressure is known as Select one: a. Welding b. Spot Welding с. Нeating d. Pressure Welding
Match the following
2
Q2B/ Answer any one of the following: 1. Define weld decay and how can be prevented 2. How can be change the grey cast iron to ductile iron
How is the removal of the backing strip noted on a welding symbol
Which statements are correct? a. Hydroforming is typically used for composite body components b. Laser welding helps to decrease the load of the body c. fastening sequence of a body is 1st engine compartment, then facet panel then venter Od. In welding, for around 600 parts per shift robotised lines are preferred.e. Robogate is employed particularly for mobile parts welding. need the right answer , if wrong will downvote