R(s) + V(s) V2(s) + V3(s) V4(s) + Vs(s) C(s) G|(s) G2(8) G3(s) V¬(s) Vg(s) H3(s) H(s) Figure 2 a) Table 2 shows the comparison of the open loop and closed loop characteristic. Fill in the basic comparison to show the difference between them. Table 2. Characteristic of open loop and closed loop Open Loop System Basis For Closed Loop System No. Comparison 1 Definition Components Аccuracy Stability Response Calibration 4 5 7 System Disturbance One Example 8 b) What is a transfer function? Consider the closed loop system shown in Figure 2. Determine the transfer function for the closed loop system, C(s)/R(s) using block reduction method. 2.

R(s) + V(s) V2(s) + V3(s) V4(s) + Vs(s) C(s) G|(s) G2(8) G3(s) V¬(s) Vg(s) H3(s) H(s) Figure 2 a) Table 2 shows the comparison of the open loop and closed loop characteristic. Fill in the basic comparison to show the difference between them. Table 2. Characteristic of open loop and closed loop Open Loop System Basis For Closed Loop System No. Comparison 1 Definition Components Аccuracy Stability Response Calibration 4 5 7 System Disturbance One Example 8 b) What is a transfer function? Consider the closed loop system shown in Figure 2. Determine the transfer function for the closed loop system, C(s)/R(s) using block reduction method. 2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Could you solve the d and e parts and explain step by step and showing the solutions clearly, please. Thanks a lot.
I need the answer as soon as possible
A causal linear time invariant system obeys the difference equation: y[n] - 2y[n-1] + 2y[n-2] - y[n-3] +0.2y[n-4] = 3x[n] + 5x[n-1] + 7x[n-2] + 5x[n-3] + 3x[n-4] (x[n] is the input and y[n] is the output) i) is the system stable? ii) Is this system minimum phase? Explain.
A Piezoelectric type
1. (s+0.2) G(s) = 5 (s+0.04) 19 - The compensator circuit (passive if possible) will be made, which is given the function at the bottom. If R1=50 MOhm is C, which of the following is it? A) 0.04 mikroF OB) 0.4 mikroF OC) 4 mikroF D) 0.4 milliF E) 40 microF
Question
Q4 Figure Q4 shows a position-control system for motion control system. Suppose that, for constant input, steady state errors less than two percent, ess< 2% is obtained. Given that G(s)=2.Q/(s³+4s²+5.Ts+2.Q). 4 ○ イー a) Find the position error constant, Kp b) Determine the gain, K value for steady state error condition as stated c) Check the stability requirement for K, using Routh-Hurwitz criterion
i need correct solution the answer might be: 5s4+15s3+1/ s3+3s2+2
Soru-1 Aşağıdaki blok diyagramların transfer fonksiyonlarını bulunuz. a) G1(s)=Y1(s)/U1(s) b) G2(s)=Y2(s)/U2(s) c) G3(s)=Y2(s)/U2(s) H(s) G3(s) U1(s) Y;(s) U2(s) Y2(s) + G(s) G1(s) G2(s) U3(s), Y3(s) G1(s) G2(s) H1(s)
5 pls keep it simple and write it clearly
Exercises: Simplify the following expressions: AB (C D+EF )(A B + CD) (2) A+B[AC +(B+C) D] (3) (A + B C ) (A B + A B C)
For the shown system, Use the Routh criterion to determine the range of stability relative to the gain K. Note that K is always positive K> 0. Type a, b, c, d, e or f R(s) C(s) K(s² + 2s) (s²–4s + 8)(s + 3) а) 1 5 c) 0 3 e) 3 < K < 8 f) not stable for any K Answer: