QUIZ 3 FALL 2020 Problem 1. For the frame shown in the figure, determine (a) Reactions at the supports (b) Axial force, Shear Force and Bending Moment at a point on BC lying at Im from point B 30 kN 15 kN 10 kN 10 kN 25 kN L12 kN/m 8 kN D B с рin HA HF 3.0 m 4.5 m 4.5 m VA 12.0 m 5.0 m 7.0 m

Q: A Liquid compressed in a cylinder has a volume of 1000 cm³ at 1 MN/m² and a volume of 995 cm³ at 2…

A:

Q: 2. Determine the deflection at point C of the beam shown in the figure (a) by double integration…

A: Given Data  E = 200 GPA I = 830 × 106 mm4 Find deflection at C using double integration method.

Q: a. In your own words, what is the difference between a positive and a negative bending moment? b.…

A:

Q: ting shown in the figure below, determine: llowable load the foundation could carry using general…

A:

Q: 5. A metallic top-hat stringer reinforced wing skin (function of the material A=150) has a width of…

A: The function of the material = 150Width =1.5 mUnsupported length =0.5 mApplied compressive load =120…

Q: Water flows through the curved pipe shown in the figure below where point X denotes the center of…

A: Given: The discharge is 1 m3/s. The diameter of the pipe at the inlet is 0.5 m. The diameter of the…

Q: The total volume of a soil specimen is 80,000 mm3 and it weighs 150 grams. The dry weight of the…

A: Find the following: a) The water content. b) Void Ratio. e) Porosity. d) Degree of saturation. e)…

Q: Problem Solving: 1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415…

A:

Q: A homogeneous linear system of algebraic equations A has infinitely many solutions B has all of its…

A: Given  Homogeneous linear system of algebraic equations

Q: 1. A soil has the following profile and a lateral stress coefficient at rest is 0.45. 0-4 G, = 2.75…

A: Given  K0 = 0.45  Take Unit weight of water  = 10Kn/m3 Water table is at 5m below the ground…

Q: 3. (Tipler and Mosca, Physics for Scientists and Engineers, 5th Ed.) Consider three charges on a…

A:

Q: A T-beam for a floor system has a slab thickness of 4" and a web thickness of 16". It has an…

A:

Q: Problem For a given sol, the following are known, G, = 2.70, moist unit weight is 20.3067&N /m², and…

A:

Q: 8. Determine the magnitude and coordinate angles of the resultant force acting at A. daB dac R in…

A:

Q: A 0.4 kg rubber ball has a horizontal velocity of 1.554 m/s at point A and goes through a projectile…

A: Horizontal velocity, Initial height, To find: The peak height of the trajectory point.

Q: Determine the amount of total excavation in BCY needed for the spread footing shown below. A…

A: Before the construction of the footing, the excavation of the land is proceeding because the…

Q: A column of 17-ft effective length must carry a centric load of 233 kips. Using allowable stress…

A: Le = 17 ft P = 233 kipsE = 29 x 106 psi  = 36 ksi

Q: Determine the moments at all supports. 2 KN 2 kN 4 kN/m 6 kN/m 2 m 4 m 4 m 3 m 1 m/ R₁ R₂ R3 V4…

A:

Q: Consider Figure FTR 1 (Taken from Geotechnical Engineer- ing Design, Ming Xiao, strictly for…

A: NOTE - Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Design a short square tied column to carry an axial dead load of 150 kips and a live load of 400…

A: Solution; Given Data; Side=a Ag=a2 in2As=3% Ag=0.03 a2 in2Ac=Ag-Ay=0.97 a2 in2F'C=4000 Psi=4…

Q: QUESTION 14 A non-potable water storage tank is at an elevation of 37 feet above the discharge for…

A:

Q: Problem 1: Beam ABC is supported by a three-bar truss at point C and at A by an elastomeric pad that…

A:

Q: F = 25kN 1) The socket wrench AB lies in the plane parallel to xy plane. 10kNm The assembly OAB is…

A:

Q: 1. For a constant head laboratory permeability test on a dine sand, the following values are given:…

A:

Q: Two planes intersect each other. What is the term for the angle formed perpendicular to the…

A: ans -b                 ans-(b) plane angle                 0ans

Q: A wood structure is assembled to support the force applied. All pieces of wood have a width of 5 in.…

A:

Q: 8. The computed latitude and departure of line AB are 0.00m and + 45.46m respectively. What is the…

A:

Q: 10.28 A reinforced concrete beam has a cross-section as shown in figure 10.22. The allowable tensile…

A: Given: A T-section beam as follows Allowable tensile stress in steel = 120 MPa Allowable…

Q: 2. s) According to Boussinesq and Westergaard conditions, determine the resulting load at a point 15…

A: 2We have formula for BoussinesqΔσ=Qz232π11+rz252We have formula for…

Q: Use AASHTO method to classify the following different group indices based on their test results. 1)…

A:

Q: 3. Which of the following is NOT a measure of forecasting errors? A. Mean absolute error (MAD) B.…

A: Explanation : Forecasting error is the discrepancy between actual and predicted demand numbers.…

Q: 8. Compute the AL and the Ad for each leg of the traverse shown below. Show the EL and the Ed as…

A: Lattitude and departure signs :  N-E : Both positive  S-E : Lattitude negative Departure positive…

Q: 21 gm of ferrous sulphate crystals are added to each cubic metre of water for coagulation with lime…

A: given- 21 gm ferrous sulphate1 cubic meter of water85% CaO

Q: In a triaxial test at failure, major principal stress was 180 kPa, minor principal stress was 100…

A:

Q: Highway curve has R = 800 m, I = 20° 00', and Pl station 3+290.600 m. Part A Determine degree of…

A: R=800mdegree of curvature=?

Q: r the slabs supported on four sides, when the ratio of the longer side and shorter side exceed be…

A: As per guidelines we need to answer only 1st question so please repost rest questions separately.

Q: kN M = kN - m

A:

Q: In what type of building code article would you see a statement describing in detail the nailing…

A: QUE:- in what type of building code article would you see a statement describing in detail the…

Q: A composite beam is under external loads as shown below. a) Draw the internal shear force and…

A:

Q: (a) What are the recoverable strains obtained at the 1,000th and 80,000th load cycles? (b) What is…

A: Introduction- Therefore, the strains recovered in a crystalline solid are those that can be handled…

Q: 7 1) 4)| Which of the following is true regarding the Moment- An internal hinge for the conjugate…

A: As per bartleby policy I can answer only 3 true/false question at a time. please re-upload again the…

Q: A hollow cylinder 80 cm long in diameter, one end closed, is immersed vertically with its closed end…

A: Let us analyse the question in step 2.

Q: (12) 2 A cylindrical srod which is fixed from both the ends as shown in fig., calculate the reaction…

A:

Q: A metal body floats at the interface of water and oil (sp, gr = 0,85) such that 35% of its volume is…

A:

Electrical Plans

An electrical plan is also known as an electrical drawing or a wiring diagram. It is a kind of visual representation which bears the blueprint symbols of all the electrical components in electrical house plans or various building construction projects. In other words, electrical plans describe electrical circuits and systems that build up the electrical house plans or building plans. An electrical engineer who works on various construction projects creates an electrical drawing. The engineer outlines the electric planning with different symbols and lines forming a detailed electrical circuit. These drawings are a means of representation for the clients, who will carry out the actual wiring process. In a nutshell, an electrical plan showcases the circuitry with the proper placement of electric components.