Determine the degree of freedom (F) of the mechanism using the general degree of freedom equation. Write down the number of limbs on the figure. Also, specify the number of joints and the degree of freedom of each marshall. b) Determine the number of common (j1) and high (j2) pairs and show them on the figure. (c) Determine the degree of freedom using Kutzbach's criterion. Does this criterion provide the correct answer for this mechanism? Briefly explain why or why not.

Q: A offset crank-slider mechanism is used in a conveyor loading device. Find the crank length in mm…

A: Here, CBDC: 107 mm below and 140 mm to right of A. Stroke: 52 mm along a 42° incline. To determine…

Q: In a swiveling joint mechanism, as shown in figure below, the driving crank OA is rotating clockwise…

A: Given: NAO = 100 r.p.m or wAO = 2π× 100/60= 10.47 rad/s ; OA = 50 mm =0.05 m; AB = 350 mm = 0.35 m;…

Q: i need a explanation what means the roll and count all nb of (link and j1 and j2) on the graph…

A: Step 1: In this image, a mechanical system with various links and joints is shown. there are three…

Q: Position and Disnlacanant Analveis

A:

Q: Draw the mechanism on the side schematically, determine the parameters of the links. Draw the…

A:

Q: Determine the forces acting on the ground and the torque, T12, to maintain static equilibrium for…

A: it is asked to solve the problem both graphically and analytically

Q: For the plow mechanism attached to a tractor is shown below draw the kinematic diagram and find its…

A: For the plow mechanism attached to a tractor is shown below draw the kinematic diagram and findits…

Q: Ki ke Ks Ks ka शान शि दा ////// गया

A: GIVEN DATA- A SPRING MASS SYSTEM GIVEN WE HAVE TO FIND EQUIVALENT SPRING STIFFNESS AND NATURAL…

Q: For the offset slider-crank mechanism shown in the figure, calculate (a) the length of stroke of…

A:

Q: Determine the dof (mobility) of the following mechanisms.

A:

Q: (d) Calculate the mobility using the Kutzbach revision of Gruebler equation. Note: You can watch an…

A: The below figure shows the list of links, joints and higher pairs in the given linkage.The numbers…

Q: a. Number of Links: L= Number of joints: J₁= Number of half Joints: J₂= Mobility= b. Number of…

A: The mobility of the mechanism also known as degree of freedom is the number of motions a mechanism…

Q: Identify the number of links, full joints and half joints, and then determine the degree of freedom…

A: Identify the number of links, full joints and half joints, and then determine the degree of freedom…

Q: gure 0₁ L 500 lb 2014 > ▾ Part C Identify the support reactions on the linkage shown in (Eigure 2).…

A: Point A , B and C are pin connection

Q: Design of Crank-Rocker Mechanisms For Problems 5-19 through 5-28, design a crank-rocker mechanism…

A: Given: θ4 = 96 deg Q = 1.2  To design crank rocker mechanism and find crank speed

Q: A horizontal board is held up by two supports. A cat sits on the end of the board, as shown. Find…

A:

Q: Q3 (Gyroscopes) The essential structure of a certain type of aircraft turn indicator is shown in the…

A: Given: The spring stiffness, K = 500 N/m The mass of uniform disk, m = 200 g = 0.2 kg The radius of…

Q: or the spring system given in Figure 1, create the element matrices as well as the global stiffness…

A: here, the force is determined by F = Keq x  so there is two spring in series  Hence  both are in…

Forced undamped vibrations

In mechanical engineering, vibration is expressed as the term that occurs due to an object's backward and forward movement about a point of equilibrium. Generally, there are three types of vibrations which are,