DA stamping device is used for work on sheet metal work piece. The puncher that moved by double acting cylinder (DAC- A) with sp stamp the sheet metal and lefur retracted back to its position. While the sheet metal inside the blank will push out using another DAC- B and retracted back with Spring return ) Design an Pneumatic-PLC circuit by using 5/2 way valve.

DA stamping device is used for work on sheet metal work piece. The puncher that moved by double acting cylinder (DAC- A) with sp stamp the sheet metal and lefur retracted back to its position. While the sheet metal inside the blank will push out using another DAC- B and retracted back with Spring return ) Design an Pneumatic-PLC circuit by using 5/2 way valve.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.5: Taper Turning

Problem 15RQ: Calculate tailstock setover for a 13.5" part with a TPF of 0.27.

See similar textbooks

Similar questions

Electro-pneumatics Sequential Circuit Problem: Initial position all cylinder are retracted. Pressing the start pushbutton makes 5 cycles. After making 5 cycles lamp is energized for 3 secs. Cycle Operation: Cylinder A extend and hold the work piece. Cylinder B extend for 5 secs. Then retract. Cylinder A retract.
Design the circuit (pneumatic/hydraulic/electro-pneumatic/electro-hydraulic) for the following problems:1.A double acting cylinder of pneumatic system will extend when two pushbuttons are pressed. The retraction is doneautomatically when either one of the pushbuttons is released.2A pushbutton is required to extend a cylinder of a pneumatic stamping machine. Once the cylinder at the full extensionposition, it will wait for 5 seconds before it is automatically retracted.3.The cylinder extends when two pushbuttons are pressed. The cylinder retracts when the set pressure of 5 bar is achieved.4.Given a hydraulic system with double acting cylinder. The cylinder extends when the lever is triggered. The retraction of thecylinder is achieved by another lever.
Please analyze and answer thank youuuu
The reversing motor,which is controlled by two power relays,can be rotated in both directions as shown in the figure beiow.When the motor is mechanically combined with a lead screw,the rotary motion is converted to a linear one,such as the one moving lef tor right on the worktable in the layout.The desired direction of rotation is selected via the two STAFIT buttons,respectively.The limit switches LS1 and LS2,located at the two extreme motion limits,ensure 1-rqtf we forget to stop the movement of the worktable,then it will stop automatically, and the mechanism of the layout will not be destroyed.Draw the circuit of automation.
1. Design a crank-rocker linkage that will move the rocker link between two extreme positions 45 de apart. The rocker should take twice the time to moving in one direction that it takes moving in the other. somyb\\; eqrad no malieb uroy dont elle est sor oldnoba mare ono mol foque (do iliw now wodor 00. aasbois.oved nov 2. If the fourbar linkage designed in question 1 is non-grashof, list two ways in which you would alter the design so that the crank is able to rotate.
It is desired to operate the pneumatic cylinder below which has to pistons A and B to stamp the die D. The piston A s returned in its back stroke by a spring, and has quick return .It is advised to use solenoid and pilot valves DCV . ( best design is to use two DCV valves ) 1- Make a complete circuit layout to operate the device above, using the appropriate symbols.2-Describe in details how your system works ( typed ) 3- Names the components of your system. 4- Any pneumatic working design will be considered as correct.
Show Circuit diagram of the problem and quantity of each part used.
Read and understand the problem then draw a pneumatic circuit diagram for it. Include complete port and component designation on your circuit diagram. No need to follow the time given in the problem, just make the forward and return stroke speed adjustable. A double-acting cylinder (1A) guides cylinder pins towards a measuring device. The pins are separated by means of a continuous to and fro movement. The oscillating motion can be started by means of a valve with selector switch. The duration of the forward stroke of the cylinder is to be tl = 0.6 seconds, the return stroke t3 = 0.4 seconds. The cylinder is to remain in the forward end position for t2 = 1.0 seconds, resulting in a cycle time of t4 = 2.0 seconds. Messfix 1A
Write and draw the following grashof's criterion and kind of grashof's four-bar mechanism such as; 1. Crank-rocker mechanism; 2. Drag link mechanism; 3. Double rocker mechanism; 4. Crossover-position or charge-point mechanism; 5 Triple rocker mechanism (non-grashof). Use technical Pen for the following: 0.2(light -for linkages and hand writing), 0.4(medium - for joints), 0.6(heavy - for fixed link or frames) use 2-4-4 template, all caps, italicized.
FLUID POWER SYSTEMS
Provide link for references 4. What are the advantages and disadvantages of using the Wet Mount technique?
Hand written plz asap... I'll upvote