measuring an inclined distance. The measured length on the slope was recorded to be 528.368 m. long. The difference in elevation between the initial point and the end point was found to be 6.369 m. The 50 m tape is of standard length at a temperature of 280C and a pull of 8 kg. During the measurement, the temperature reading was 350C and tape was supported for a full

Q: Q1: Use slope-deflection method to analyze the continuous beam shown in figure (1): (EI- Constant)…

A: EI = constant Analyze the beam using slope deflection method.

Q: Determine the amount of deflection at free-end and also the maximum deflection using double…

A:

Q: 30 kN 20 kN 20 kN D m E m F L K H

A:

Q: Mohr’s Circle ; Direct shear test was performed on dry, sandy soil. The specimen is 50 mm in…

A:

Q: Determine the force P required to force the 17° wedge under the 96-kg uniform crate which rests…

A:

Q: 7. Calculate the vertical displacement AA at A with the graphic multiplication method. (20') 9…

A: Step 1Introduction and questionsThe task is to calculate the vertical displacement ΔA​ at point A…

Q: Subject: Structural Theory Topic: Area-Moment Method Draw diagram and handwritten solutions. Box…

A: Step 1: Step 2: Step 3: Step 4:

Q: 3. Determine the reaction of supports using slope deflection method. El is constant. A 20 kN/m 6 m…

A: Given Data  Find support reaction using slope deflection method.

Q: Q.3 Torsional Formula A circular shaft of diameter 300 mm and length 2.5 m is subjected to a torque,…

A: Given data- A circular shaft- Diameter D=300 mm, Length L=2.5 m, Angle of twist θ=0.025 radian, To…

Q: W = 30 K/m L= 3m E- 18GPA;b=200 mm %3D d: 400 mm

A:

Q: 1. The 50-kg homogenous smooth sphere rests on the 30° incline A and bears against the smooth…

A:

Q: Situation #2 El is Constant (Assume El = 1 kN-m²) B A kN/m A 7 m B= 8 A= 5 20. Determine the…

A: Given data  EI = 1 KNm2  Find  1. Location of maximum upward deflection from B 2. Maximum upward…

Q: use the virtual work method to determine the deflection at point C of the beam shown

A: Given :- A beam is shown with two point load of 200 kN and 100 kN Modulus of elasticity constant (E)…

Q: PROBLEM 2: A support block is acted upon by two forces as shown. Knowing that the coefficients of…

A:

Q: a = 8.3 m, b = 3.1 m, c = 10.0 kN/m, d = 32 kN. %3D %3D d kN d kt c kN/m BA "b" m "b" m

A:

Q: A spring is used to stop a 55 kg package which is sliding on a horizontal surface.  The spring has a…

A: Let us analyse the question in step 2.

Q: In the Experiment-2 of Young's modulus, if the beam having a length of 2 m has a width of 60 mm and…

A: Givn datadeflection=0.2 mmlength=2000 mmload=area=30×60=120000…

Q: Neslyn used a 50m steel tape used to measure a certain distance. It was later found that the tape is…

A:

Q: Analyze the beam 4P (kN) 2P (kN/m) 80° 3m 3m 4m 3m

A:

Q: For the beam loaded as shown in the figure below, determine the following unknowns using any…

A:

Q: Integration Method = 10 kN/m Compute deflection at the free end (maximum deflection). В A YB = Ymax…

A:

Q: From the given figure: Let P = 26KN, L = 8m, a = 3m if the equation of the slope is Ely = Pª (-+L),…

A:

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A: The FBD for a given beam can be drawn as ;Consider vertical forces ;Take moment at A = 0From…

Q: Answer ALL of the following A. Classify according to USCS having: D 0.075 mm. Deo=0.02mm. D =…

A: D90= 0.075 MM  D60= 0.02 mm  D30= 0.005 mm  D10= 0.0005 mm  Plasticity index = 45%  Plastic limit =…

Q: Determine whether the 15-kg block shown is in static equilibrium under the loadings shown, and…

A:

Q: Problem 4. Determine the maximum deflection and slope.

A:

Q: the slope at A 7. Determine 8. Determine the slope at B 9. Determine the location of the maximum…

A: Given:- EI = Constant = 1 kN-m2 Y = 32 X = 868 A = 5 To find:- Slope at A Slope at B Location of…

Q: A 30-m steel tape weighing 1.68 kg. is of standard length under a pull of 50 N, supported for full…

A:

Q: Question 2 The bulldozer shown in the Figure below is fitted with a blade, 1.1 m high and 5 m wide.…

A: Given :

Q: Soil with a unit weight of 20 kN/m3 is excavated at 3m below the ground surface. Calculate the shear…

A:

Q: (b) A 50-kg machine tool is mounted on an elastic foundation. An experiment is run to determine the…

A:

Q: Ex-6. A steel tape with a cross-sectional area of 0.039 cm2and weighing 0.909 kg has a length of…

A: Given  Cross section area=0.039cm^2 Weight=0.909kg Length=30.009m Tm=20℃ Ps=5.5kg Slope=4% PT=12kg…

Q: n Figure (1) below. (b) If W-10 kN/m, and L -3.5 m, determine the sla en at 2 m from point A.…

A:

Q: P10.030 For the beam and loading shown, use discontinuity functions to compute: (a) the deflection…

A:

Q: PROBLEM 5 The uniform block, 4'x 3'as shown weighs 2001b. It is pulled up the incline by the force…

A:

Q: Determine the maximum deflection Integration Method.

A:

Q: For the beam loaded as shown in the figure below, determine the following unknowns using any…

A: To find deflection at point C

Instruments for Surveying

Surveying is the practice that determines the relative three-dimensional positions of many different points on the earth’s surface. There are various instruments used in Surveying like Theodolites, Total station, Tripod stands, Plane table, etc. for measuring horizontal angle, vertical and sloping angle, which are very useful for giving accurate and precise measurement.