measured on (10 m) height from If the wind speed measured on the earth is (2.5 m/s). What is the height of wind turbine tomer should be if the turbine work om (5m/s). Discuss the height from the earth surface with roughness if the surface are :- 1. Sandy surface is vary between (al-013) Trees surface is vary between ( 0-2 3. Hilly Surface is vary between 2. between (0-20-25) between (1-5-6-9)

measured on (10 m) height from If the wind speed measured on the earth is (2.5 m/s). What is the height of wind turbine tomer should be if the turbine work om (5m/s). Discuss the height from the earth surface with roughness if the surface are :- 1. Sandy surface is vary between (al-013) Trees surface is vary between ( 0-2 3. Hilly Surface is vary between 2. between (0-20-25) between (1-5-6-9)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Block A has a mass of 100 kg and the coefficient of friction is 0.20. Determine the friction force between A and B. 500 N 1 90° Bed A 30° 450 N B Dreble m .
Question 1: The Industrial building shown is lculed im lat open country, grasslands, the wind speed is V= 120 mph. Determine the vertical wind pressure for both transvers and longitudinal wind direction, assume K-1. Arrange the information in table. e-22 22 160 50 Dniis in fet
A)determine total metacentri. Height Mbo when its rolled in one side B)angle of inclination when its rolled to one side in (degrees) C)total draft in oneside in (meters)
Question 3 The wind blows uniformly on the front surface of the metal building with a pressure of 1.8 kN/m?. Determine the resultant force it exerts on the surface and the position of this resultant. y 2.5 m 1.0 m 2.5 m. 2.5 m.
Determine the tension T in the belt needed to overcome the tension of 200 lb created on the other side. Also, what are the normal and frictional components of force developed on the collar bushing? The coefficient ofstatic friction is μs = 0.21.
Kindly solve this using Double Integration Method (DIM). Show complete solution and show how to get the reactions. Thank you. 120 ŁN-m
40 L/s of 20C water (ν = 1.007*10^(-6) m^2/s). Flows through 1,200 ft of6-in diameter new steel pipe with ks = 0.0002 ft. The friction loss must be:
2. A block of wood 30cm square and 60cm long weighs 318 N. Will the block float with its sides vertical as shown? 60 ст 30 ст 30 ст Side vlew End view
Determine the smallest value of P for which the system of two blocks will be in equilibrium. Friction is negligible except for the surface under block B. c. 82.50 N d. 97.30 N a. 75.00 N b. 60.90 N A 20 530 N B Р. 350 N As=0.15
75 mm 75 mm 150 mm d 150 mm d Water 3 m 0.63 m Hg Problem 4.67 Probie 4.67. Calculate the velocity head in the 75 mm constriction.
A wood-stave pipe 120m long is to carry 3,400liters/sec across a ravine. Water enters one end of the pipe from an open flume, and discharge at the other end into another flume, and discharges at the other end into another flume. If the difference in elevation between the water surface in the flume is to be 1m, determine the necessary diameter of pipe, assuming well-designed transition (k=0.10, k=0.20) and neglecting the effect of velocity in the flumes. Use f=0.013.
the school building has a flat roof. it is located in an open area where the ground snow load is 0.68kn/m square. Determine the snow load that is required to design the roof.