C Programming "Functions" (See Fig. 5.1) A student is trapped in a room of a burning building. How long should aladder be in order for a fireman to reach him through the window located at the 4th floor?The window is 8 ft high and the ladder's base must be 6 ft from the edge of the buildingsince there is an obstruction. Make a program to compute the ladder length.Hint: Use pow(x,y) and sqrt(x) functions to apply Pythagorean's Theorem of Fig. 5.2Hypotenuse (H)8 ftOpposite (O)Angle90Adiacent (A)6 ftFig. 5.1 LadderFig. 5.2 Pythagorean Theorem: H² = A? + O?

The question is solved in the C programming language with the help of the Pythagorean Theorem. Here,…

Answered: Make a program to compute the ladder…

Engineering

Computer Science

Make a program to compute the ladder length.

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter14: Numerical Methods

Section14.4: The Secant Method

Problem 3E

See similar textbooks

Similar questions

(Mechanics) The deflection at any point along the centerline of a cantilevered beam, such as the one used for a balcony (see Figure 5.15), when a load is distributed evenly along the beam is given by this formula: d=wx224EI(x2+6l24lx) d is the deflection at location x (ft). xisthedistancefromthesecuredend( ft).wistheweightplacedattheendofthebeam( lbs/ft).listhebeamlength( ft). Eisthemodulesofelasticity( lbs/f t 2 ).Iisthesecondmomentofinertia( f t 4 ). For the beam shown in Figure 5.15, the second moment of inertia is determined as follows: l=bh312 b is the beam’s base. h is the beam’s height. Using these formulas, write, compile, and run a C++ program that determines and displays a table of the deflection for a cantilevered pine beam at half-foot increments along its length, using the following data: w=200lbs/ftl=3ftE=187.2106lb/ft2b=.2fth=.3ft
(Practice) Run Program 7.10 to determine the average and standard deviation of the following list of 15 grades: 68, 72, 78, 69, 85, 98, 95, 75, 77, 82, 84, 91, 89, 65, and 74.
(General math) Modify the program written for Exercise 2 so that it accepts the x- and y-coordinates of two points. Have your program determine and display the midpoints of the two points (using the formula given in Exercise 2). Verify your program by using the following test data: Testdataset1:Point1=( 0,0)andPoint2=( 16,0)Testdataset2:Point1=( 0,0)andPoint2=( 0,16)Testdataset3:Point1=( 0,0)andPoint2=( 16,0)Testdataset4:Point1=( 0,0)andPoint2=( 0,16)Testdataset5:Point1=( 5,5)andPoint2=( 5,5) When you have finished your verification, use your program to complete the following chart:
(Electrical eng.) a. The voltage gain of an amplifier is given by this formula: voltagegain=[275 23 2 +0.5 f 2 ]n f is the frequency in Hz. n is the number of stages in the amplifier. Using this formula, write, compile, and run a C++ program to determine the value of the voltage gain for a four-stage amplifier operating at a frequency of 120 Hz. Your program should produce the following display: At a frequency of xxxxx hertz, the voltage gain is yyyyy Your program should replace xxxxx with the frequency and yyyyy with the voltage gain. b. Manually check the value your program produces. After verifying that your program is working correctly, modify it to determine the voltage gain of a 12-stage amplifier operating at a frequency of 9500 Hz.
(Thermodynamics) The work, W, performed by a single piston in an engine can be determined by this formula: W=Fd F is the force provided by the piston in Newtons. d is the distance the piston moves in meters. a. Determine the units of W by calculating the units resulting from the right side of the formula. Check that your answer corresponds to the units for work listed in Table 1.1. b. Determine the work performed by a piston that provides a force of 1000 N over a distance of 15 centimeters.
(Statics) An annulus is a cylindrical rod with a hollow center, as shown in Figure 6.7. Its second moment of inertia is given by this formula: I4(r24r14) I is the second moment of inertia (m4). r2 is the outer radius (m). r1 is the inner radius (m). a. Using this formula, write a function called annulusMoment ( ) that accepts two double-precision numbers as parameters (one for the outer radius and one for the inner radius), calculates the corresponding second moment of inertia, and displays the result. b. Include the function written in Exercise 5a in a working program. Make sure your function is called from main(). Test the function by passing various data to it.
(Practice) The volume, v, and side surface area, s, of a cylinder are given by these formulas: v=r2ls=2rl r is the cylinder’s radius, and l is its length. Using these formulas, write and test a function named cylinder() that accepts a cylinder’s radius and length and returns its volume and side surface area.
(Practice) Determine the value of the following expressions, assuming a=5,b=2,c=4,d=6,ande=3: a.abb.a!=bc.db==cbd.ac!=dbe.db==cef.!( ab)g.!( abc)h.!( cba)i.bca
(Automotive) a. An automobile engine’s performance can be determined by monitoring its rotations per minute (rpm). Determine the conversion factors that can be used to convert rpm to frequency in hertz (Hz), given that 1rotation=1cycle,1minute=60seconds,and1Hz=1cycle/sec. b. Using the conversion factors you determined in Exercise 7a, convert 2000 rpm into hertz.
(Numerical) Heron’s formula for the area, A, of a triangle with sides of length a, b, and c is A=s(sa)(sb)(sc) where s=(a+b+c)2 Write, test, and execute a function that accepts the values of a, b, and c as parameters from a calling function, and then calculates the values of sand[s(sa)(sb)(sc)]. If this quantity is positive, the function calculates A. If the quantity is negative, a, b, and c do not form a triangle, and the function should set A=1. The value of A should be returned by the function.
(Debug) Determine and correct the errors in the following programs. a.includeiostreamusingnamespacestd;intmain()width=15area=lengthwidth;coutTheareaisareab.includeiostreamusingnamespacestd;intmain()intlength,width,area;area=lengthwidth;length=20;width=15;coutTheareaisarea;return0;c.includeiostreamintmain()intlength=20;width=15,area;lengthwidth=area;coutTheareais,area;return0;
(General math) If a 20-foot ladder is placed on the side of a building at an 85-degree angle, as shown in Figure 3.11, the height at which the ladder touches the building can be calculated as height=20sin85. Calculate this height by hand, and then write, compile, and run a C++ program that determines and displays the value of the height. After verifying that your program works correctly, use it to determine the height of a 25-foot ladder placed at an angle of 85 degrees.