MAKE A FREE BODY DIAGRAM Síx forces are acting on the mesh as shown in the figure below. Find the total torque produced by the given forces at points (a) A and (b) B. 255N L.0 m! 112 1.0m 384 N 429 B 328 183N

Q: 1. Determine the maximum speed that the cars of the roller-coaster can reach along the circular…

A: Given:Radius of curvature, r=20 mmaximum acceleration, amax=2.5 g

Q: acceleration in ft/s² at the bottom of its swing (point D)

A: Calculate the normal acceleration at point D.

Q: gâge and a manometer are attached to a tank to measure pressure. Given the reading on the pressure…

A:

Q: A rectangular plate with notches (see figure) has dimensions h=5.75 in, h1 = 5 in and the plate…

A:

Q: Send correct answer

A: To convert world energy consumption from quadrillion Btus to the equivalent quantities in other…

Q: VA radial bush seal consists of a cylinder with an inner radius of 20 mm and an outer radius of…

A:

Q: Q.5: A piston/cylinder contains water with quality 75% at 200 kPa. Slow expansion is performed while…

A:

Q: PROBLEM 4: The tank contains a liquid having a density as shown. 10 in 5 ft 10 ft 7ft Pliquid = 2.52…

A: Given data: ρliquid=2.52 slug/ft3 Need to determine the unit weight of the liquid, weight of the…

Q: Required information Determine the tensile and yield strengths for the following materials: SAE 1040…

A: Material SAE 1040 cold drawn steel is given.  Let us find tensile strength and yield strength of…

Q: A steel bar 200 mm in diameter is turned at a feed of 0.25 mm/rev with a depth of cut of 4 mm. The…

A: Given data: The diameter of the steel bar is D = 200 mm. The feed rate is f = 0.25 mm/rev. The…

Q: Is it possible for a designer to use exergy analysis recommendations to improve the performance of a…

A: To find :- Exergy ananlysis

Q: The cantilevered handle in the figure is made from mild steel that has been welded at the joint For…

A: Given   For mild steel      Young's modulus, E = 30.46 X 106 psi                                 Fy…

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: For the given state of stress, determine the planes with compressive normal stress equal to 15 MPa.…

A:

Q: Considesing the relationshb Tas =dU+ befween the enry(s), interred enegy (U), poresscre (p),…

A: Option d is correct.

Q: two 5 cm diameter, 15 cm long aluminum bars (k=176W/m(degrees Celsius)) with ground surfaces are…

A:

Q: erial when longitudinal strain is 0.12mm/mm and transverse strain is -0.03

A: Given data  Longitudinal strain=0.12mm/mm  Transverse strain=-0.0396mm/mm

Q: Determine the steam condition for the steam properties on the table below. Write: SHV if it is a…

A: Mollier Diagram provides all the necessary information for various conditions of steam. By analyzing…

Q: From a beam bending test on a cantilever beam, the following data was collected, what is the…

A: Given: The table of mass and their respective deflections are given below, mass (g) deflection in…

Q: Convert a -7 kPa (negative 7 kiloPascal) pressure to an absolute pressure in kPa. (Note: the…

A:

Q: ExJA 20° straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a…

A:

Q: 3 in. 45 15° 30 30 kg in. 50 lb Figure 3 Figure 4 4. Three cables are joined at the junction ring C.…

A:

Q: You are designing a cantilever beam of rectangular cross-section and of fixed length. Your goal is…

A: Consider the equation shown below for the bending stress.

Q: In (Figure 1), F₂ = 410 N. Figure Fy 250 N 30% < 1 of 1 ▼ Part A Determine the magnitude of the…

A:

Q: 7. A SAE steel column has a circular cross-section of 16 mm in diameter and a length of 320 mm. The…

A:

Q: Determine the specific volu ideal-gas equation of state

A:

Q: Sketch a plot that contains a lateral strain for a material undergoing a temperature change which…

A: Given : Same temperature change for 2 materials one results in elastic deformation and another…

Q: 8/ What is the principal difference between the two subdivisions of the polymeric composites: therm…

A: 8.1 answer Two types of polymers are used as matrix materials for fabrication composites:…

Q: You are expected to design a simulation environment for a bicycle with a kinematic model. The…

A:

Q: ermine the force P required to force the 11° wedge under the 99-kg uniform crate which rests against…

A:

Q: i attached the screenshot please help me to find the answer of the  wrong one

A:

Q: Calculate the horizontal force Pon the light 14° wedge necessary to initiate movement of the 58-kg…

A:

Q: Consider the liquid shown in figure to be kerosene at 20°C. Given h1 = 6.4 ft and y = 50.3 lbf /…

A:

Q: A certain amount of an ideal gas is initially at a pressure p, and temperature T,. First, it…

A:

Q: Párt A Determine the velocity of the gear rack C. Express your answer to three significant figures…

A:

Q: 4. Determine the horizontal force exerted on block E. F = 150 16 6 in BD 11 8 in a B 150 6 in. D E

A:

Q: Which one of the folowing is not correct ?

A: Given; The maximum shear stress theory predicts that shear yieldvalue ζy is 0.5 times the tensile…

Q: Problem 9.10 Part A Determine the equivalent state of stress on an element at the same point…

A:

Q: 1 [Short Answer) A pitot tube is used to measure the velocity of incoming flow, the velocity is 9…

A: The velocity of flow is The static pressure is .

Q: What is the ideal mechanical advantage (IMA) for the inclined plane shown below if H 0.3m and L 3 m?…

A: Given:W=300 NF=50 NH=0.3 mL=3 m

Q: Draw the Mohr's Circle (Fig. 3) as accurately as possible on a graph paper. (a) Using equation find…

A:

Q: is a measure of sensitivity of a strain gauge and is represented as the ratio of to A. BSF,…

A: Strain gauges are the devices which are used to measure the stresses in equipments or parts.

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.