Major Assignment 2 (Replacing Test 2) Question 3 A beam of mass 17 kg and length 2.4 m is attached to a wall with a hinge. The other end of the beam is supported by a rope which is attached to the wall. The beam, rope and wall form an equilateral triangle. What is the tension in the rope? 2.4 m APR 21

Major Assignment 2 (Replacing Test 2) Question 3 A beam of mass 17 kg and length 2.4 m is attached to a wall with a hinge. The other end of the beam is supported by a rope which is attached to the wall. The beam, rope and wall form an equilateral triangle. What is the tension in the rope? 2.4 m APR 21

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The screw is subjected to two forces F1 and F2.Determine:a. the magnitude b. direction of the resultant force
O A fectangular loop of wive is polled at a constant acceleration from a region of Zero magnetic field into a region of uniform magnetic field (directed perpendicular to the Plane containing the wive 100p), where the loop is completly immersed in the magnetic fie ld. During the process, Current indueed in the lop . the a will increace linearly uith time will increase linearly with the Square of 7ime will be zero will be a constant non-zero value
i need the answer quickly
A horizontal meter stick of mass M is held in static equilibrium by 2 supports: • a vertical upward force F₁ at the position x1 (measured from the left end of the stick) • a vertical upward force F2 at the position x2 (measured from the left end of the stick) Check all the following which are true statements. There may be more than one correct answer! F F2 x1 x2 F1 F2 = Mg F1x1 = F2x2 either x1 or x2 must be less than 50cm
Can you use a slanted rope attached from the wall to the end of the beam if that rope breaks when the tension exceeds 170 N? The beam is light.
1
Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is us = 0.35. Express your answer to three significant figures and include the appropriate units. ? M = Value Units Submit Request Answer Provide Feedback Next > Figure < 1 of 1 M D Pearson
The drum, shown in Figure 3 has a weight of 419 N and rests on the floor. The coefficient of static friction between the drum and the floor is µ= 0.6. If dimensions a = 0.6 m and b = 0.9 m, determine the smallest magnitude of the force P that will cause impending motion of the drum. P Figure 3
Constam Part A How many rotations per minute would a Ferris wheel with diameter d = 24 m need to perform in order for its riders to feel weightless at the highest point? Express your answer using two significant figures. 阳 ΑΣφ f = rpm Submit Request Answer Provide Feedback P Pearson MacBook Air
Q2 / The arm of patient was placed into traction, stretch of the shoulder from a length of 0.56 m to 0.562 m. The shoulder has diameter 2.06 cm. Note that the bone has Young's modules of 1.6 x 1010 in tension, what force was used to stretch the shoulder?
The tolerance is -+1 in the 2nd significant digit
Problem #5 One end of a uniform { = 4.00m long rod of weight w is supported by a cable at an angle of 0 = 35° with the rod. The other end rests against a wall, where it is held by friction (see figure). The coefficient of static friction between the wall and the rod is us 0.500. Determine the minimum distance x from point A at which an additional weight w (the same as the weight of the rod) can be hung without causing the rod to slip at point A. に4.00m o=35° X