READ THE INSTRUCTIONS: Do not round off intermediate values when using them to solve subsequent calues; however they may be written up to 4 decimal places. final answer should be rounded off up to 4 decimal places.I'll upvote if it is correct and compelete. Thank you y840 NF38°2Thisatas if it were our aum35°31400 N2.1 kNa. Determine the magnitue of P and F(in N) if the resultant of the five forcesshown is 1000 N directed 45 degreesNorth of East.b. If the components of the resultantforce are found along the u-axis and acertain v-axis and it is known that thecomponent along the u-axis is 510 Nat 35 degrees South of East, what isthe magnitude along the v-axis?c. Determine the angle of the -axiswith respect to the horizontal.

To find the magnitude of the force F and P

Answered: magnitue of Pand F

Engineering

Civil Engineering

magnitue of Pand F

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute the moment about point A. Use F-1400 pounds and theta-25 degrees. Show all work on your paper to receive credit. With your written final answer, include 3 significant digits, units and a direction arrow. Type your answer for the moment about A below with 3 significant digits. Do not type units with your numeric answer.
600mm 100mm 50mm x 50mm hole 500mm 10mm A 100mm Figure 3 Show that the horizontal neutral axis is 77.56mm below B. Hence, show that the moment of inertia around this horizontal neutral axis is 3178942345mm4. Show the division of your area on a sketch on your answer sheet. a) (use the answers in (a) for (b), (c), (d) and (e)) b) Draw the 3D normal stress distribution of the section subjected to M = -10 kN.m. Draw the shear stress distribution of the section if the section is subjected to a shear force of 10KN. c) d) What part of the shear force is carried by the flange? e) What part of the bending moment is carried by the flange
1. Answer each problem following the proper format (GIVEN, REQUIRED, SOLUTION). 2. Do not round off intermediate values when using them to solve subsequent values; however, they may be written up to 4 decimal places in your answer sheets. Final answers should be rounded off up to 4 DECIMAL PLACES. 3. Box the final answers.
Name of Friends Weight in kilogram Arianne 90 Sunshine 75 Sushi 58 Gemini 63 Eliot 88 Saskei 54 Jariw 43 Mhuxa 37 Kartana 105 Balivna 66 Ariler 82 Derite 55 Daniel 98 Kareine 40 1. Arrange the given data from lowest to highest 2. Find two values of each quantile. One lower and one upper. Show your solution. Compute for Q, and Q6, Dz and D12. P33 and Pgo
Show your complete solution. The final answer should be -11/17
Provide quick solution for the given problem. Solve and box the final answer. WRITE LEGIBLY.
Please write the solutions legibly. Good feedback will be given. Use 4 decimal places.
On a three-dimensional cartesian plane, Points A, B, C, and D are to be plotted as follows: POINT: A: B: C: D: Determine the x-component of vector AB. Express your answer in terms of the units on the DROP-DOWN MENU (if applicable). Observe 3 decimal places. The error threshold is t 2.50 % Relative to the right answer. DO NOT INDICATE UNITS ON THE ANSWER BOX Answer: Determine the y-component of vector AB. Express your answer in terms of the units on the DROP-DOWN MENU (if applicable) Observe 3 decimal places. The error threshold is t 2.50 % Relative to the right answer. DO NOT INDICATE UNITS ON THE ANSWER BOX Answer:
How to solve?
EXACT/ NON EXACT DIFFERENTIAL EQUATIONS (10)
pls help! write the complete solutios and legibly. UPVOTE will be given! Answer in 4 decimal places. Engineering Mechanics
5.0 m (100+SN) KN> 144 KN 5.50 m E 6.0 m C 7.0m K 5.0 m O 120 KN 96 KN M U W Note: SN is the sum of your Student Number, e.g. 201802475=2+0+1+8+0+2+4+7+5 = 29 Instruction: Solve the following problem completely using portal method and write the solutions neatly in the plate template. Summarize your final answers at the end of each problem. Round off your answers to 3 decimal places. 1. Portal Method: The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X are rigid supports. Determine the following: a) The shear forces in columns and girders. b) The axial forces in columns and girders. c) The moment at the end of each member. d) Summarize your results by drawing the frame with the internal forces. 4.0 m R 4.20 m 4.50 m 5.0 m