machine mounted on elastic supports, is free to vibrate vertically. The machine has a mass of 40 kg and rotor out-of-balance effects are equivalent to 2 kg at 150 mm radius. Resonance occurs when the machine is run at 621 rpm. the amplitude of vibration at this speed being 45 mm. Determine the amplitude when running at 500 rpm and find the angular position of the out-of-balance mass when the machine is at its highest position during vibration.

machine mounted on elastic supports, is free to vibrate vertically. The machine has a mass of 40 kg and rotor out-of-balance effects are equivalent to 2 kg at 150 mm radius. Resonance occurs when the machine is run at 621 rpm. the amplitude of vibration at this speed being 45 mm. Determine the amplitude when running at 500 rpm and find the angular position of the out-of-balance mass when the machine is at its highest position during vibration.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A mass weighing 4 lbs. stretches a spring 1.5 inches. The mass is given a positive displacement of 2 inches from its equilibrium position and released with no initial velocity. Assuming that there is no damping and that the mass is acted on by an external force of 2cos3t lbs., formulate the IVP describing the motion of the mass. What is the position of the mass at any time t? Determine also the period and amplitude of motion of the mass.
mo A 100 kg machine has an unbalanced mass of 1 kg, which is rotating at a constant speed of 500 rpm at an offset of 0.2 meters. Calculate the amplitude of the centrifugal force that will be acting on the ground if the machine is directly anchored to the ground. Also calculate the stiffness of the elastic pad that will be placed under the machine such that only 1/10 of this force will be transmitted to the ground. 0-ot m
i need the answer quickly
A reciprocating engine runs at 110 rpm with a stroke of 1.6 m and a connecting rod 2.4 m in length. It imparts simple harmonic motion to a 250 mm diameter piston. When the crank pin is 32º beyond top dead centre the pressure on the piston is 0.8 MN/m². Calculate EACH of the following: (a) the instantaneous velocity of the piston; (b) the instantaneous torque at the crank pin; (c) the instantaneous acceleration of the piston.
Derive the differential equation of motion for the system shown in its equilibrium position. Neglect the mass of link AB and assume small oscillations. Use the values m1=22 kg, m2=31 kg,k=800 N/m, c=163 N·s/m, a=340 mm, and b=610 mm and calculate the damping factor
A mass of m = 12 kg is suspended by a spring of stiffness of S = 1 KN/m from a fixedsupport. The mass vibrates freely with amplitude of 0.008 m. Ignore the effect of dampingand mass of the spring. Calculatei. The maximum restoring force.ii. The natural frequency.
A spring extends by 5 centimeters when loaded vertically with 2.5kg of weight. A new weight of 1.75kg was attached to it and was displaced 6cm from its new equilibrium position and was released from rest. Determine the frequency of vibration in rad per second?
A block having a weight of 8 lb is suspended from a spring having a stiffness k = 40 Ib/ft. If the block is pushed y = 0.4 ft upward from its equilibrium position and then released from rest. What is the amplitude of the vibration? Assume that positive displacement is downward
A weight attached to a spring of stiffness 3.0 lb/in has a viscous damping device. When the weight is displaced and released, the period of vibration is found to be 1.80 seconds and the ratio of consecutive amplitudes is 4.2 to 1.0. Determine the amplitude and phase angle when a force F-2cos(3t) acts on the system.
Which one is correct please?
The equation of motion of a one – degree – of – freedom spring – mass – is given as; 6 * + 0.4c x + 3550 x = 0. If the mass of the system is displaced 150 mm and released without an initial velocity, determine the number of cycles executed before the amplitude of displacement is reduced to 10 mm when the damping coefficient is 300 - s/m. Also, determine the critical damping coefficient of the system. -damper system
A belt pulley is designed as a flywheel. it has a moment of inertia of 100kgm^2 and is supposed to be accelerated from a resting position to a rotational frequency of 600 min^-1 within 15 seconds. you have to calculate the acceleration torque without considering the friction of the bearing