m A fluid flows at 0.001 - through a 100- mm diameter pipe. Determine whether the flow is laminar or turbulent if the fluid is • a) hydrogen (v = 1.08 x 10¬4 m² /s b) air (v = 1.51 x 10-5 m² /s) c) gasoline (v = 4.06 x 10-7 m²/s) d) water (v = 1.02 x 10-6 m² /s) E) mercury (v = 1.15 x 10-7 m² /s %3D

m A fluid flows at 0.001 - through a 100- mm diameter pipe. Determine whether the flow is laminar or turbulent if the fluid is • a) hydrogen (v = 1.08 x 10¬4 m² /s b) air (v = 1.51 x 10-5 m² /s) c) gasoline (v = 4.06 x 10-7 m²/s) d) water (v = 1.02 x 10-6 m² /s) E) mercury (v = 1.15 x 10-7 m² /s %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A roof tank supplies water as shown in Figure 1. Calculate the minimum height (H) in metre required to maintain a 1.5 m head pressure and 1.0 l/s flow rate at the point of discharge. Given the following data: G.I. pipe diameter d = 25 mm Friction factor f = 0.009 Loss coefficient: ki = 0.2 k2 = 10 Gate Valve Globe Valve Elbow k3 = 2 k4 = 0.5 k5 = 20 Entrance loss at tank Water meter 116 FIGUEE I I un lom'
16
The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L Suction Pressure= 220mmHg vacuum , 425mm below the pump C.L Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.
Use four decimal places in all solution
determine the flow rate at pipe 1 and pipe 2 and pipe 3.please show your complete solution.
topic: parallel pipes hydraulics
URGENT PLS
Q.15 Water is flowing through two pipes one of 10 mm diameter and second of 5 mm diameter and both are discharging in 12 mm diameter pipe. The rate of flow in 10 mm diameter is 1.0 c.c./s. If the Reynolds number of 12 mm diameter pipe flow is 4000, determine the rate of flow in 5 mm diameter pipe. Consider kinematic viscosity equal to 6.5 x 10-7 m²/s.
Determine the diameter of the pipe if the fluid flows @ 20 L/s and the velocity head is 5m in mm *
The water surface shown below is 10 m above the datum. The pipe is 425 mm in diameter and the total loss of head between point (1) in the water surface and point (5) in the jet is 3 m. Determine the discharge Q. (m3/s). Round your answers in 3 decimal places.
1) A manometer is attached to two pipes as shown. If knowing mercury SG is 13.6, sea water SG is 1.035, and fresh water p is 1,000 kg/m³, determine the pressure difference between two pipelines at the centers. Fresh Water h. -60 cm Air hair -70 cm hea <- 40 cm Mercury Sea Water hi -10 cm
P10.) Determine the flow in each pipe shown in the figure. Assume f = 0.02 for all pipes. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes