LRC circuit contains a parallel-plate capacitor with plates of area 16.34 m^2, separated by 1.29 mm and completely filled with dielectric (dielectric constant k= 2.85), 39.85 Ohm resistor and toroidal solenoid inductor with 1,971.02 turns of wire, a cros-sectional area of 3.47 cm^2, and mean radius of 4.32 cm. The components are connected in series to an emf source operating with a 88.45 V amplitude at 115.25 Hz. What is resonance angular frequency (rad/s?

LRC circuit contains a parallel-plate capacitor with plates of area 16.34 m^2, separated by 1.29 mm and completely filled with dielectric (dielectric constant k= 2.85), 39.85 Ohm resistor and toroidal solenoid inductor with 1,971.02 turns of wire, a cros-sectional area of 3.47 cm^2, and mean radius of 4.32 cm. The components are connected in series to an emf source operating with a 88.45 V amplitude at 115.25 Hz. What is resonance angular frequency (rad/s?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What should be installed to power the DC water pump, from [stream-turbine-motor-________- water pump]? Do I need battery or Voltage regulator of this? It is better if you have an idea to suggest.
please answer all question which four ) no need to write your explnation 6.A current transformer is a A.transformer used with an AC voltmeter B.transformer used with a DC ammeter C.transformer used with a DC voltmeter D.transformer used with an AC ammeter 7.The primary winding of a current transformer has A.a larger number of turns B.a few turns only C.no turns D.intermediate number of turns 8/ Relation between primary winding and secondary winding for a potential transformer is given by A.n = Np ⁄ Ns B.n = Ns C.n = 1 ⁄ Np D.n = Ns ⁄ Np 9.Two wattmeters connected to measure the total power on a three-phase system supplying a balance load read W1 = 10.3 kW and W2 = –2.3 kW, respectively. Calculate the total power. A.–8.0 kW B.8.0 kW C.–12.6 kW D.12.6 kW
i need the answer quickly
List the basic concepts involved in house wiring?
In which of the following wind energy conversion system, guy wire may be required? O a. Vertical axis wind turbines Ob. Horizontal axis wind turbines O c. Up wind turbines O d. Down wind turbines
When computing complex circuits, why is it advisable to use Kirchhoff’s Rules?
i need the answer quickly
10 - What is the figure below? A) Vavien switch installation B) Plug-socket installation C) Commutator switch installation D) Dimmer installation E) One-way switch installation
The hole on the drawing below is required to be perpendicular to the bottom surface and centrally located on the plate regardless of the size of the feature and regardless of the sizes of the datum features. In order of precedence, which datum features are missing in the feature control frame? (select all correct answers) Ø2.505 -2.510 0.005 E C A B Odatums A, D, E Odatums A, D Odatum A O datums D, E, A O datums A, E, D 1 I 6.00 4.00 1.00
l11 answer 1 2 3
Which type of Insulator is used in Substations to support connections for High Voltage Switchgears, Current Transformers, and etc.? O A. STRAIN TYPE O B. PIN TYPE O C. POST TYPE O D. SUSPENSION TYPE