**TABLE 16.3: Lifting Capacities in Pounds for a Tower Crane (Continued)****Jib Model:**| Maximum Hook Reach | L1 | L2 | L3 | L4 | L5 | L6 | L7 | Hook Reach ||---------------------|----------|----------|----------|----------|----------|----------|----------|------------|| | 100' 9" | 119' 9" | 138' 9" | 157' 9" | 176' 9" | 195' 9" | 214' 9" | || | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 13' 6" || | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 52,500 | 48' 9" || | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 51,400 | | 51' 0" || | 55,200 | 55,200 | 55,200 | 55,200 | 51,500 | 48,300 | 45,600 | 53' 6" || | 55,200 | 55,200 | 55,200 | 50,700 | 47,100 | 44,600 | 42,100 | 60' 6" || | 46,200 | 46,200 | 46,200 | 42,800 | 39,700 | 37,400 | 35,200 | 70' 0" || | 39,400 | 39,400 | 39,400 | 36,500 | 34,100 | 31,900 | Low Ball Construction Co. has determined that the heaviest load to be lifted on one of its projects weighs 22,000 lbs. From the tower crane location on the building site, the required reach for this lift will be 100 ft. The crane is equipped with an L7 jib and a four-part hoist line (Table 16.3 load chart). This critical lift is of a piece of mechanical equipment and will require a 1,000-lb spreader bar attached to a 200-lb set of slings. If assembled in the proposed configuration, can the crane safely make the pick?

Given: load to be lifted = 22,000 lbs Height to be lifted = 100 ft Equipment = L7 jib Spreader bar = 1000 lb Slings attached to the bar = 200 lb To find: The crane can safely make the pick.Solution: From the given table For L7 jib and a four-part hoist line: for the hook reach of 100 feet. The maximum load that the crane can carry is 22,600 lbs The load that needs to carry along with the spreader and slings: Total load = 22,000+1000+200=23200 lb 23200>22600 Since the load that needs to carry is greater than the given limit. Hence the crane cannot safely make the pick.Answer: The crane cannot safely make the pick. Total load that needs to carry> Maximum load that crane can carry at 100 ft23200>22600

Engineering

Civil Engineering

Low Ball Construction Co. has determined that the heaviest load to be lifted on one of its projects weighs 22,000 lbs. From the tower crane location on the building site, the required reach for this lift will be 100 ft. The crane is equipped with an L7 jib and a four-part hoist line (Table 16.3 load chart). This critical lift is of a piece of mechanical equipment and will require a 1,000-lb spreader bar attached to a 200-lb set of slings. If assembled in the proposed configuration, can the crane safely make the pick?

Low Ball Construction Co. has determined that the heaviest load to be lifted on one of its projects weighs 22,000 lbs. From the tower crane location on the building site, the required reach for this lift will be 100 ft. The crane is equipped with an L7 jib and a four-part hoist line (Table 16.3 load chart). This critical lift is of a piece of mechanical equipment and will require a 1,000-lb spreader bar attached to a 200-lb set of slings. If assembled in the proposed configuration, can the crane safely make the pick?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 4 1p Four wheel loads rolls as a unit across a 18-m span. The loads are 50 kN, 40 kN, 30…

Q: Discuss in detail the function of cranes and hoists and list the different types

A: This question is related to the Building design and Construction from Civil Engineering. In this…

Q: 4. Assuming the crate weighs 100 lbs, calculate the tension in each example and explain if a…

Q: basic equations and forces analysis are needed for reservoir and pipe folw.

A: The artificial or natural storage of water with help of dam is known as a reservoir.

Q: 1. A wire rope is used with total load of 8500 kg and bending load of 55,000kg. If the breaking…

A: Solution-The given values are as followsTotal load=8500kgBending load =55000kgStrength of the…

Q: Use the joist guide from the Vulcraft catalog to select the most economical K-series joist that…

Q: 5.b the diagram below represents the chassis rail of the lorry above. Draw the shear force and…

A: Data given Find the shear force and bending moment diagram

Q: THE FOLLOWING INFORMATION IS TO BE USED IN THE NEXT 2 (TWO) QUESTIONS. Twelve (12) lines are strung…

A: Given:- A frictionless block-and-tackle system of a drilling rig is given The total number of…

Q: ced 0.3 kPa for self-weight of the joi 9.00 m wide. Assume an allowable e ps and include them in…

Q: Considering the given cantilever beam, columns and their cross-sections in figure 2, then justify…

A: Beam: Maximum bending moment on the beam is Mmax Mmax=50 kN×3 m=150 kNm=150×106 Nmm Maximum bending…

Q: If a joist made out of 2x5 lumber were to span 10 ft and to carry a linear load of 90 #/ft, what is…

Q: For the floor beam/girder given and the loading shown, the maximum bending moment occurs at Pu L/3…

Q: A vertical lifeline rope with a rope grab must Reach the lower level or have a stop below the brake…

A: A vertical lifeline rope with a rope grab must : all of the above

Q: Compute the maximum combined loads using the recommended ASDexpressions from the AISC. D = 9000 lb,…

A: Determine the maximum combined loads for AISC using the below relation: where,

Q: 2.5.11. A sliding gate 10 ft wide and 6 ft high is installed in a vertical plane and has a…

Q: Draw the free-body diagram for the following problem.The jib crane shown.

A: Free body diagram is a graph or image of an object in which all the forces, moments and reaction…

Q: Identify the trend: As the operating radius increases, as the boom length increases, as the boom…

A: This question is related to the Construction Equipment from construction technology from Civil…

Q: A 25 story building has it columns spaced at 32 ft between centers in each direction. The floor dead…

A: Given that: Spacing of columns = 32 ftDead load = 150 psfLive load = 100 psf

Q: Sketch #1 shows a three stage working deck personnel scaffold suspended from TWO OUTRIGGER BEAMS…

A: These days, in current tall structures, horizontal deflection prompted by wind or tremor powers are…

Concept explainers

Management of Materials

Materials form the basic ingredient or the raw supplies before the final product. Materials cover the inventory storage in typical warehousing. All manufacturing processes and production processes require different materials.

Question

**TABLE 16.3: Lifting Capacities in Pounds for a Tower Crane (Continued)**

**Jib Model:**

| Maximum Hook Reach | L1 | L2 | L3 | L4 | L5 | L6 | L7 | Hook Reach |
|---------------------|----------|----------|----------|----------|----------|----------|----------|------------|
| | 100' 9" | 119' 9" | 138' 9" | 157' 9" | 176' 9" | 195' 9" | 214' 9" | |
| | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 13' 6" |
| | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 52,500 | 48' 9" |
| | 55,200 | 55,200 | 55,200 | 55,200 | 55,200 | 51,400 | | 51' 0" |
| | 55,200 | 55,200 | 55,200 | 55,200 | 51,500 | 48,300 | 45,600 | 53' 6" |
| | 55,200 | 55,200 | 55,200 | 50,700 | 47,100 | 44,600 | 42,100 | 60' 6" |
| | 46,200 | 46,200 | 46,200 | 42,800 | 39,700 | 37,400 | 35,200 | 70' 0" |
| | 39,400 | 39,400 | 39,400 | 36,500 | 34,100 | 31,900 |

Low Ball Construction Co. has determined that the heaviest load to be lifted on one of its projects weighs 22,000 lbs. From the tower crane location on the building site, the required reach for this lift will be 100 ft. The crane is equipped with an L7 jib and a four-part hoist line (Table 16.3 load chart). This critical lift is of a piece of mechanical equipment and will require a 1,000-lb spreader bar attached to a 200-lb set of slings. If assembled in the proposed configuration, can the crane safely make the pick?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer as soon as possible
Please answer question 2, thanks. 1.For the loading and material information shown below, according to EC3, design and check the bending and shear capacities of steel beam which is 10 m long for carrying the listed loading. Information: Beam span length = 10 m, Bay width = 6 m, Slab depth = 20 cm, Partitions = 0.75 kN/m2 , Imposed load = 2.5 kN/m2 , Concrete density = 24 kN/m3 , Steel grade = S355 . Design the beam as a restrained beam as lateral restraint is provided by the concrete slab. Simple support condition of beam ends can be assumed. Check also the deflection of the beam and see if it can satisfy the serviceability limit states or not. 2. For the beam in Question 1, check the corresponding reduced moment capacity for high shear case assuming that VEd / Vpl, Rd = 0.7 .
Determine the number of a glulam column 3.0 m in length that support an axial load of 120 kN. The column is to be built with 35mm thick and 200mm wide laminations of Yakal lumber (E = 9.78 GPa, Fc = 15.8 MPa). Assume a normal load duration, wet service condition and fixed-end connection with lateral support at both ends.
1. Given the following information, determine the appropriate LRFD load combination and calculate the load acting on a typical roof joist (plf). The joists span 30 ft and are spaced 5 ft on center. Select the lightest K-series joist from the LRFD joist selection tables. Since this is for a roof joist, allowable deflection is L/240. In addition to the series designation, also indicate the capacity of the joists. Dead Load: 28 psf Roof Live Load: 20 psf Snow Load: 31 psf Rain Load: 23 psf Wind Load: 33 psf (Upward)
Can you please solve the calculations with equations and step by step and use space Gass software for diagrams?I will be grateful to you for this help.All the best and Thank you so much in advance.
help on both please