Locate the centroid (X only) of the shaded area y =12 - 3 x 3 m Fig.1.A 3 m y = 4 – 2 m -2 m

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: where did 144 come from

A:

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: A bcc (111) surface has the following (3x1) adsorbate structure: Select all of the following LEED…

A: Solution: Given Data:

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: For the frame shown below, Is supported by pins at C and D. Determine the magnitude of reaction at C…

A: Consider the free body diagram of the member CBA as shown below.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Water falls vertically downward from an open faucet with an initial velocity of 47 cm/s. If the…

A:

Q: Draw the box closing mechanism given in the figure in the given dimensions. Determine the velocities…

A:

Q: The equation of the unit circle is _______________.

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: Q.2 A cantilever beam of length / = 5 m, flexural rigidity El in MPa, and mass m = 1950 kg carries…

A:

Q: What is the length and wall thickness of the vertical bear

A: For figure 2,  drawing and the type of symbols present

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: how can I get the 85 α

A:

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A:

Q: For figure (4): The ring is subjected to two forces (F, and F2). Suppose that the resultant force…

A: Given data:

Q: Choose three types of Reuleaux lower pairs, and answer the following, F.1 Write down their names?…

A:

Q: A multi-stage pump, 260 gpm capacity is installed in a well 27 ft below the static water level.…

A: Given data:  The capacity of the pump is given as Q = 260 gpm = 0.579 ft3/sThe total discharge head…

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: Crossed center lines are used in the .. . view Longitudinal Horizontal Circular All

A: Solution:

Q: Calculate the number of degrees of freedom The value must be a number 11 Calculate the number of…

A: Full joint is the joint which has area or surface contact, and half joint is the joint which has…

Q: (12m) ladder weighs 200N and is ed against a smooth vertical wall its lower and (6m) from the wall

A:

Q: Figure 1 of 1 30 40 F2

A: Given, F1 = 210 N F2 = 510 N Angle between two forces = θ = 40°

Q: At a given moment four link mechanism OABO, is in the position shown on the figure and OA= AB = AO =…

A:

Q: (d) Water flows in two different horizontal pipes having a height difference of 55cm. A U- tube…

A:

Q: Through the two pipes in Figure 6 flow equal flows of water. data: Pipe diameter No. 1: 200 mm -…

A:

Q: The point 1/4 of the way from (1,-3, 1) to (7,9, –9) is A. (4,3,-4) O B. (3/2,3,-3/2) OC.…

A: A point's coordinates are a pair of integers that define its precise position on a two-dimensional…

Q: Starting from rest, Block A moves down the inclined plane with velocity given by 3t“, where t is in…

A:

Q: why is F3 0

A: Hydrostatic Force- A resultant force which acts on a submerged surface due to the pressure loading…

Q: PLS ANSWER 8-14

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: 1+1?

A: Basics of CALCULATION.

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.