llowing signals: e X3 (t) = sgn(2t) – sgn(t)e obvious from the definition of sgn(t) that sgn(2t) = sgn(t). Therefore . %3D

Q: What are the steps for plotting points on microstation uisng offset, station, side and elevation?

A: We need to tell about steps for plotting points on microstation uisng offset, station, side and…

Q: grounding and bonding requirements    17. Which of the following is effective when it comes to…

A: Solve the first question, unless the student has asked for a specific question to be solved, subject…

Q: do you have any other method to solve this problem??

A: In the given circuit,we need to find above mentioned parameters.

Q: What is the meaning of the acronym, XLPE? A. EXTRA LOW POLYESTER EQUIPMENT B. CROSS-LINED POLYETHYL…

A: In this we will write about XLPE....

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: Considering the termination temperature ratings of the equipment used in residential wiring, discuss…

A: In residential wiring the selection of conductor ampacity is always determined based on the 60°C…

Q: Please answer this diligently. Other answers in the internet seems wrong. Please help me understand…

A: First, we need to calculate the base current. The base current (Ibase) can be calculated using the…

Q: hat is the approximate voltage amplitude and frequency of the waveform below?

A: Disclaimer: "Since you have asked multiple questions, we will solve the first question for you. If…

Q: Airframe Electrical System Question: In general, what factors areconsidered when selecting the…

A: While manufacturing, the sizes of the wire are selected according to a known standard called as…

Q: Airframe Electrical System Question: What is the temperature operating limit of tin-coated…

A: The temperature operating limit of tin-coated copper-stranded electrical wire (600 V rating) is…

Q: Airframe Electrical System Question: What type of wiring method is most often employed in the design…

A: The type of wiring mostly  employed in the design and operation of aircraft electrical and…

Q: Overcurrent devices do not have to be readily accessible if ____. Select one: A. LOCATED WITHIN A…

A: Overcurrent devices do not have to be readily accessible if LOCATED ADJACENT TO THE EQUIPMENT WHERE…

Q: 14.a. Which test can be used to measure splice loss? A. Tensile measurement B. OTDR C. Bit error…

A: In this question,  We need to Choose the correct options.

Q: illustrated in your reading material, the plug-in busway for motor Branch circuits has tap- off…

A: Correct option is c part.

Q: What is the minimum distance between conduits in a junction box straight through pull? A. 6 times…

A: The correct option from the given options will be option D) 12 times. For junction box calculations,…

Q: What NEC article contains a list of the electrical installations that are covered by the NEC?…

A: The NEC (National Electrical Code) is a globally recognized standard for the safe installation of…

Q: . The only exception to the need for all information technology equipment to be satisfactorily…

A: Equipment grounding is mainly done for user protection.it is a non-current carrying element. A. In…

Q: 14.a. Section 250.94 requires that an IBT be accessible for inspection and termination and have the…

A: 14.a. IBT stands for Intersystem Bonding Terminal. According to NEC Section 250.94 (B) An IBT be…

Q: Airframe Electrical System Question: Why is bare copper electrical wire not suitable for aircraft…

A: The reason why Bare copper is not suitable for aircraft use is that:It develops a surface oxide…

Q: Airframe Electrical System Question: By what means should aircraft electrical circuits/wires be…

A: Aircraft electrical circuits/wires should be protected from excessive current by means of Circuit…

Q: Which of the following is?are an application of electrimagnets. A) relays, B) generations, C)…

A: An electromagnet is a type of magnet in which the magnetic field is produced by an electric current.

Q: 14.a. Where should fiber optic cables that are fixed in cable trays be installed? A. In riser spaces…

A: In this question we are to determine : Where should fiber optic cables that are fixed in cable…

Q: . You're installing type AC cable. The armor coating of type AC cable is allowed for use as an…

A: Requirement for the installation and constructions for AC 'Armored cable' are located in Article…

Q: What is the approximate voltage amplitude and frequency of the waveform

A:

Q: Using the notation scheme for defining manipulator configurations, draw diagrams of the following…

A:

Q: What is the meaning of calculated load?

A: Since many different loads are connected to an electrical supply, it is extremely important to know…

Q: 20.a. What's the primary disadvantage of using copper conductors? A. Durability B. Cost C.…

A: 20. (a) Although one of the most electrically conductive materials known, copper is easily corroded…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.