List and state the uses of ten major components in the power system  State three importance of process automation.

Q: 1. Are the theoretical calculations and measured values are equal? Explain?

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: Give 5 Examples of Control Systems. Provide at least a 2-3 Paragraphs explaining why is it an…

A: Types of control system  Open loop control system ( feedback signal will not taken into…

Q: Question No. 1: [10 Marks] [CLO-1] Draw only the block diagram to demonstrate the complete PCB…

A:

Q: One of the following is the example for process control system. a. Water level controller b. Radar…

A: Cement Industry is an example of process control system.Advanced process control is used in cement…

Q: To operate a system that will draw high current, this type of integrated would you use it, why?…

A:

Q: What is lightning? Describe the mechanism of the lightning discharge.

A: Lightning- It is a discharge of electrical energy of very short duration and high voltage between a…

Q: Principles of Machine Shop Practice

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: 1. What is the nameplate reading on the machine? What inferences can be drawn from it?

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A washing machine is supplied with hot and cold water from two different supplies. Draw the bock the…

A: Given, Two inputs with cold and hot water supply. The flow of hot water as well as the cold water…

Q: . Which one of the following methods should be used to test a totally enclosed machine?

A: The answer of given question: The Retardation method should be used to test a totally enclosed…

Q: 1- What are the function of a) Execution unit b) Bus interface unit

A: As per bartleby guideline for more than one question asked only first is to be answered please…

Q: Draw an elementary diagram of a fractional horsepower, manual motor starter

A: An elementary diagram of a fractional horsepower, manual motor starter is given below:

Q: Which of the following is not a type of energy requiring lockout or tagout procedures

A: Which of the following is not a type of energy requiring lockout or tagout procedure?

Q: Design a PLC program that will correctly execute the following industrial control process: A part is…

A: We need to draw and explain the PLC diagram for the given operation. The given operation and…

Q: Control system This question I need it about half an hour

A:

Q: 3. Write any four differences between NC and CNC machines.

A: Ans. Given below

Q: 4 - Which of the given is not related to the traction motor? A) Uses electricity, generates…

A: Although major parts of traction motor is  Power supply (Electricity) , Converter (rectifiers)  ,…

Q: Hard drive etc and its relation to faraday's law hand written please.

A: To read data on hard disc Faraday's law is used as explained above.

Q: 1. What specific requirements which ought to taken into consideration when developing an Electrical…

A: NOTE: “Since you have asked multiple question, we will solve the first question for you. If you want…

Q: -a What tool should be used in bending metallic conduits? A. Heat gun B. Hydraulics C. Pipe bender…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What is electrical machine.

A: Electrical Machine: It is a device that converts mechanical energy into electrical energy and vice…

Q: AIWhat is the difference between clippers and clampers ? sketch the * .circuit

A:

Q: 3. What are the advantages and disadvantages of star delta starter? Machine A.C

A:

Q: 1. What are the difference between automatic regulating system and process control system. 2. What…

A: Automatic control system: 1.This type of system is a self-operating system. 2.Automated Control…

Q: Why there is a need to study Electrical skill problems?

A: Electrical skiil

Q: Explain the energy changes involved in the generation of electrical energy from diesel generator.

A: Diesel generator: it is a device which generates electrical energy  from chemical energy  by the use…

Q: is defined as the art and science of measurement and control systems.

A: Explanation: Instrumentation is defined as the art and science of measurement and control systems.…

Q: A proportional system of control system. How to disable OFF-SET ? Draw example for Process line…

A: The oscillations around the set point (known as oscillation) in some processes may be too severe to…

Q: What are power tool

A:

Q: D.a. Which one of the following PM programs is usually the largest for a typical manufacturing…

A: D.a Mechanical PM programs is usually the largest for a typical manufacturing facility. Hence,…

Q: Write a report on system control strategies and techniques used in engineering.

A: The term system control refers to the controlling of any system. In terms of electrical system, it…

Q: Which 1 below is NOT PLC's configuration types Modular Unitary O Rack mounted Automation O

A: Asked that which one below is NOT PLCs configuration types

Q: Name some tools and appliances which contain universal motors.

A: A Brief About Universal Motor:- A Universal Motor is a commutation type AC motor which is used with…

Q: Topic; Plc based automatic intelligent car parking system. Q1; Concepts, principles and theories…

A: Answer Block diagram : Functional diagram of PLC: PLC performance: The block diagram of the…

Q: 1.a. The typical PM work order is normally generated by a computer and then issued A. directly to…

A: 1(a). The typical PM work order is normally generated by a computer and then issued by the program…

Q: What is an example of a closed-loop control system? Select one: a. a traditional dishwasher b. a…

A: Which one is closed loop system

Q: List the important terms for an electro-mechanical system.

A: According to the question we have discuss the electro-mechanical system.

Q: List and explain elaborately 10 limitations and 10 advantages you currently foresee in the field of…

A: Mechatronics is a multidisciplinary engineering system design with combination of mechanical,…

Q: Q/ Do you observe any relation between the system damping ratio and the system settling time.

A: We need to tell about relationships between damping ratio and settling time

Q: electrical machines Explain how the experiment is done by drawing the connection diagram of the…

A: Explain how the experiment is done by drawing the connection diagram of the alternator idle test.…

Q: For a control system shown in figure below, find the value of K & Ke

A:

Q: Control systems  solve all parts or i will dislike

A: According to question: With U(S)=0, the block diagram is reduced to the form as given below: When…

Q: block diagram of the electromechanical energy conversion of a power tool

A:

Q: f the following parameter will define the closeness of the measured value to the true valu Accuracy…

A: i) correct option is accuracy. accuracy" is defined as the degree of closeness of a measurement to…

Q: What technology choice is appropriate for the safe usage of power tools ?

A: Electrical tools provide engineering managers and maintenance with a way to meet both the physical…

Q: Explain about the use of PLC in conveyor (moving material machine) and how to implement it using…

A:

Speed control of motor

Speed control by DC motor-speed controller is required to realize variable speed drive. Whenever a motor drives a particular load, it is called drive, and variable speed drive refers to a load requiring variable speed. All this is obtained by a DC motor speed controller.