Lines of levels are run from BM1 and BM2 over three different routes. If the elevation of BM1 is 100 m above the sea level. (Diff. in Elev) Between BM1 & BM2 632.81 m Route Length A. 10 16 В 632.67 m C 40 633.30 m a.) Determine the probable weight of route B. b.) Determine the most probable difference in elev. of BM1 and BM2. c.) Determine the most probable elevation of BM2. BM1 is lower than BM2

Q: Please use slope and deflection method to calculate the moment at the fixed support A. 54kN/m A 15m…

A: From the given fixed beam and it is required to calculate moment at the fixed support A by using…

Q: A rectangular concrete beam 341 mm wide and 382 mm deep is simply supported over a span of 11.58 m.…

A:

Q: (a) the location of the resultant; (b) the factor of safety against overturning; and (c) the factor…

A: Top width CD, B t =5m Coefficient of friction=0.6 For calculating base with of each sections, From…

Q: A storm water discharge of 1.5 m/s flows along a reinforced concrete box culvert with n = 0.015 and…

A:

Q: Solve the Member GI and FG.

A:

Q: An electrical worker stands in the bucket that hangs from a pin at end D of the boom of the cherry…

A: To find internal force at point E

Q: 6 24 Water flows at a depth of 2 m in a 3 m wide rectangular channel. At a downstream section the…

A:

Q: 2. A concrete dam is triangular in cross section and 30 m high from the horizontal base. If water…

A:

Q: Penetration 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Penetration (mm) 2 4 6 8 10 12 Load (KN) 2 4 6 8…

A: The CBR test was first developed in California, USA, to determine the bearing value of highway…

Q: Calculate the plastic moment strength about the strong axis of a built-up I-beam with flange plates…

A:

Q: in the process of solving the series

A:

Q: Part 2: By Super Position Consider the simple supported beam shown in the Fig. a. Determine the…

A:

Q: F EI EI a- + F=kx=k(1) k=? *k is Flexural stiffness

A: The solution is: As we have assumed that the hinge support is the fixed support.

Q: Find the point(s) of intersection (POls) for the following system of equations. Round your answers…

A: To determine the points of intersection of the given system of equations.   Given, fx=-5x2+2x+12…

Q: A solid shaft of 30 mm in diameter has a rated output of 20 kW. If it powers the shaft at 12 Hz,…

A:

Q: ANSWER THE FOLLOWING PROBLEM QUESTION "Loaded beam". SHOW YOUR SOLUTION AND BOX THE FINAL ANSWER…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: C-time elapsed until the blocks touch.0

A:

Q: A) identify the best line. B) What is the forward and back bearing of the best line? C) Tabulate the…

A:

Q: 3. Oil is flowing in a pipe under the condition shown. If the total head loss from point 1 to 2 is 3…

A: Head loss : The amount of head, pressure, or energy lost by water passing through a pipe or channel…

Q: (b) Time for 90% consolidation in the field with this soil with a 2.5 m thickness where only the top…

A: Given:- Clay specimenH=12.7 mmDouble drainaged=H2=6.35 mmt=28.4 min

Q: A couple, M, of 6 kNm is applied to the beam shown, causing it to bend in the horizontal plane. The…

A: Determine the values of the maximum tensile and compressive stress in the beam. Also, calculate the…

Q: -3m- el. 8 m -2m- -3m- Figure 4a el. 6 m el. 4 m el. 0 m

A:

Q: iven, graph and box the final an

A: Buoyancy force is FB=Vsubmerged×ρwater=30×1×3.25×1gmcc=97.5gWeight of…

Q: Please

A:

Q: O A long excavation with vertical sides and depth-to-width ratio of 0.5 is to be made in a deep…

A:

Q: Determine the minimum diameter d of the rod to safely support the load. The rod is made of a…

A: Calculate the maximum moment of beam and shear force Calculate the moment of inertia of a circle and…

Q: For the retaining wall shown, determine the active force per unit width of the wall using Rankine's…

A:

Q: 50° 140 kips 10 in 11 in 10 in A B 20 kips 35 kips 81 kips Tnis is nor your Cwn property so do not…

A:

Q: Determine the reactions at the supports and forces at hinge B acting on member CBA. * 0.6 m 500 N…

A: We have to determine the value of reaction at supports and force at hinge B.

Q: 4 in. 4 in. 2 in. 1 in. P 1.8 During the tension test, the wooden specimen on the left is subjected…

A:

Q: Consider the non-interacting tanks in the figure below. Resistances R 1 and R 2 are linear. The flow…

A:

Q: RA= RB= Vmax= KN 2 decimal places KN 2 decimal places KN 2 decimal places

A:

Q: Locate the centroid of the figure below from x and y axis. a 30 in b 17 in 10 in d 5 in e 18 in e x2…

A:

Q: The spring is initially compressed by 35 cm and suddenly released with the system at rest. If the…

A: Given: The mass of lighter block m1 is 3 kg. The mass of heavier block m2 is 7 kg. The spring…

Q: 1. A 3m by 3m square footing carries a uniform pressure of 100 kPa. Plot the lateral variation of…

A: In construction, the footing is the lower end of a column, pillar or wall that is enlarged with…

Q: A faucet is shown on the figure below. A force of P = 1100 lb is exerted : t both ends of the faucet…

A:

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.